The water is flowing through a pipe having diameters 40 cm and 15 cm at sections land 2 respectively. The rate of flow through pipe is 35 litres/s. The section 1 is 7 m above datum and section 2 is 3.5 m above datum. If the pressure at section 1 is 36 N/cm?, find the following by neglecting losses:

The water is flowing through a pipe having diameters 40 cm and 15 cm at sections land 2 respectively. The rate of flow through pipe is 35 litres/s. The section 1 is 7 m above datum and section 2 is 3.5 m above datum. If the pressure at section 1 is 36 N/cm?, find the following by neglecting losses:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q4. A conical pipe has diameters at the two ends of 0.5 m and 1.5 m and is 15metres long. It is…

Q: Q5. A pipe of diameter 20 cm and length 2000 m connects two reservoirs, having difference of water…

Q: What water level H must be maintained in the tank as shown in Fig. P. 3.5.20 to deliver a flow rate…

Q: In the system of reservoirs shown below, the flow of Reservoir 1 to Reservoir 2 is Q=15 cfs. At…

A: Consider the given data

Q: The water is flowing through a pipe having diameters 45 cm and 15 cm at sections land 2…

Q: 3. Determine the flow rate of water, in m3/s, at 5 C though the piping system as shown in the…

Q: QI: À) Oil relative density (r.d = 0.88) flows in an inclined pipe at a rate of 0.15 m/s as shown in…

A: d1=30cmd2=15cmSoil=0.88Q=0.14m3/sec\V1=QA1=0.14π4×(0.3)2= 1.98m/secV2=QA2=0.14π4×(0.15)2=…

Q: Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of…

Q: A water supplying pipe of diameter 14 cm, is used to pump the water to the house in the Tanuf hill…

A: Given that, diameter of pipe= 14 cm =0.14m height of the hill from ground=…

Q: Please include a free body diagram Three pipoes A,B and C coonected in seies discharges 160 L/s of…

Q: Q3: The Figure shows a horizontal pipe used to provide a fluid from a container. The pipe inlet…

A: Given: Pipe pressure P1=150kPaInlet diameter D1=1cmOutlet diameter=2.5cm

Q: In the figure below, the flow velocity is 7.6 m/s. If d=10.1 cm and D=14.3 cm. Calculate the head…

Q: A pipe, diameter 15 cm, leaves a straight pipe with a diameter of 10 cm at point A, and later…

A: Given Data: Length of 10 cm pipe, L=700 m

Q: The water is flowing through a pipe having diameters 40 cm and 15 cm at sections 1and 2…

Q: Q2/the water is flowing through a taper pipe of length 100 m having diameters 600mm at the upper end…

Q: A horizontal pipe of diameter 0.2 m is suddenly enlarged to 0.3 m. If the rate of flow of water…

A: Let smaller pipe be pipe-1 and larger pipe be pipe-2. From the data given in question, Diameter of…

Q: With velocity of 10 m/s in the 347 mm diameter pipe in the figure shown, determine the discharge in…

Q: Q.4. In the system shown in figure, the water flow rate ,Q= 0.5 m3/s and pressure P=20 kPa are…

A: In a steady flow system, the mass flow rate entering the system is equal to the mass flow rate…

Q: The power 455 W is required to transmit 8 x 10-3 m3/s of water. Find the loss of head due to…

A: Given Data Flow rate , Q=8*10-3 m3/s Power =455 watt g=9.81 m/s2. Density of water 1000 Kg/m3.

Q: The water is flowing through a pipe having diameter of 185mm and 142 mm at section (1) and (2)…

A: Given Data The flow rate is: c=56 L/sec=56×10-3 m3/sec The diameter of pipe at section (1) is:…

Q: The water is flowing through a pipe having diameters 40 cm and 15 cm at sections Tand 2…

A: As per our guidelines, we are supposed to solve only three sub-parts if multiple sub-parts are…

Q: Q3: The 6-cm-diameter pipe as shown in Figure H.I contains glycerin (p = 1260 %3D kg/m', u= 1.49…

Q: The water is flowing through a pipe having diameters 40 cm and 15 cm at sections 1and 2…

A: It is required to determine velocity head at inlet and outlet

Q: Water is flowing in a piping system as shown tin figure, Find the i. diameter of section 2 pipe. ii.…

Q: Water is transported in a pipe, at an average flow rate of Q = 50 L/s. Calculate the pressure…

A: Given: The flow rate, Q = 50 l/s The energy added by the pump, H = 10 m

Q: Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2,…

Q: a! Water flowing through a tapering pipe having diameters of 300mm and 150mm at section one and two…

A: Calculate the velocity at section 1. v1=QA1 Here, Q is the discharge, v1 is the velocity at section…

Q: The water is flowing through a pipe having diameters 30 cm and 21 cm at sections 1and 2…

Q: The water is flowing through a pipe having diameters 30 cm and 20 cm at two sections 1 and 2,…

Q: A vertical pipe in the form of a cone has a diameter of 45 cm at the top and 92 cm at the bottom and…

Q: The water is flowing through a pipe having diameters 40 cm and 17 cm at sections land 2…

Q: Q4. A conical pipe has diameters at the two ends of 0.5 m and 1.5 m and is 15metres long. It is…

Q: Calculate the flow distribution in the system shown in the figure below. The liquid that is…

Q: The tube has a diameter of 0.4m, suddenly expanding to a diameter of 0.8m, and the flow rate is 0.4…

Q: 4: Water flow through a pipe at 5L/s as shown in figure. If gage pressure of 12.5kPa, 11.5kPa and…

A: The head loss can be calculated using the Bernoulli's equation which is given below as-…

Q: The oil flows through the vertical venturi tube as shown in the figure. The venturi inlet has a…

A: Given data given setup of venturi meter

Q: A ship of 8500 tons displacement has a double bottom tank 11 m wide divided longitudinally in half…

A: Given: The ship weight, M = 8500 tons The width of the tank, b = 11 m The density of fuel = 0.85…

Q: Find the discharge of water flowing through a pipe 40cm diameter placed in an inclined position…

Q: Please try to answer in text Water flows through 100 mm diameter pipe from A to B. The velocity is…

A: Hydraulic grade line is defined as piezometer head.

Q: Q2. The turbine shown in figure 2 develops 3000 kW when the water flowrate is 24 m /s. The head loss…

Q: Q2/ Four pipes A, B, C, and D form a system of pipes that connects two reservoirs A and B, as shown…

Q: 3. A pipe of diameter 400 mm carries water at a velocity of 25 m/s. The pressures at the points A…

Q: A 6.0 cm diameter horizontal pipe gradually narrows to 4.5 cm. When water flows through this pipe at…

A: we can solve this question by using :- 1)continuity equation 2) Bernoulli equation

Q: 4: Water flow through a pipe at 5L/s as shown in figure. If gage pressure of 12.5kPa, 11.5kPa and…

Q: Pb # 3: A horizontal 110+(Reg.No./100)-mm diameter pipe (f = 0.027) projects into a body of water…

A: I have answered Pb#3. Have a good day.

Q: The machine C shown in Fig. (3) Is it turbine or pump? What is the water power (kilowatt) associated…

Q: Water flows through the vertical elbow in Figure 2 and exits to atmosphere. The pipe diameter d, =…

Q: (a) Water, at 20°C, is being siphoned from a large container through a constant diameter hose, as…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: A pipe, diameter 15 cm, leaves a straight pipe with a diameter of 10 cm at point A, and later…

Q: Galvanized iron pipes with a roughness height of 0.40 cm are used to deliver water from reservoir A…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

(ii) difference in datum head (Unit in m) =
Pressure head at section 1 (Unit in m) =

The water is flowing through a pipe having diameters 40 cm and 15 cm at sections 1and 2 respectively. The rate of flow through pipe is 35 litres/s. The section 1 is 7 m above
datum and section 2 is 3.5 m above datum. If the pressure at section 1 is 36 N/cm?,
find the following by neglecting losses:
(ENTER ONLY THE VALUES BY REFERRING THE UNIT GIVEN IN BRACKETS)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

please answer asapWater flows downwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses
A pipe 50 cm in diameter carries water (l0°C} at a rate of 0.5 m 3 / s. A pump in the pipe isused to move the water from an elevation of 30 m to 40 m. The pressure at section 1 is 70kPa gauge, and the pressure at section 2 is 350 kPa gauge. What power in kilowatts and inhorsepower must be supplied to the flow by the pump? Assume h L = 3 m of water and α 1 =α 2 = 1. Find the following Draw the Schematic diagram Drive the energy equation Calculate pump head Power requirement
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
A horizontal pipe of diameter 0.2 m is suddenly enlarged to 0.3 m. If the rate of flow of water through the pipe is 0.2 m3/s and the intensity of pressure in the smaller pipe is 100 kPa, then find (i) the head loss due to sudden enlargement, (ii) power loss due to enlargement and (iii) intensity of pressure in the larger diameter pipe.
Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses
The water is flowing through a pipe having diameters 20 cm and 10 cm at sections 1and 2 respectively. The rate of flow through pipe is 35 litres/s. The section 1 is 6 m above datum and section 2 is 4 m above datum. If the pressure at section 1 is 39.24 N/cm2, find the intensity of pressure at section 2. Sketch the arrangement.
Water flows through a garden hose at a rate of 1 l/s. The upstream diameter of the hose is 2.5 cm, and the nozzle outlet has a diameter of 1 cm. Determine the upstream pressure (gage pressure).
Water flows at the rate of 0.80m3/s in a 900-m long pipe. The total head loss in the pipe is 4m. Which of the following most nearly gives the diameter of the pipe using the Darcy-Weisbach formula with f = 0.018?
After analyzing the flow type in a refinery oil (s = 0.8, v= 1.94x10-4 ft2/s) flowing through a 9inch diameter pipe at (41/1000) ft3/s. Find the following a)centerline velocity b)the velocity at r = 2inch c)the frictional factor d)the shear stress at the pipe wall and e)the head loss per foot of pipe length.
A horizontal water pipe of 15 cm diameter converges to a 7.5 cm diameter. If the pressures at the two sections are 400 kPa, and 150 kPa respectively, calculate the flow rate of water in cubic meters per second
reservoir with water pressurized pipe diameter is 5 cm. The head loss in the system as given by hL= 5V^ 2/ 2g. The height between the water surface and the pipe outlet is 400 m. A discharge of 0.11 m3 /s is needed. What must the pressure in the tank be achieve such a flow rate? Assume a turbulent flow.
2.4) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.