The water system in a suburban area consists of an old200mm pipeline 760m long which conveys water from apump to a reservoir whose water surface is 107m higher thanthe pump. VWater is pumped at the rate of 0.07 m/s.Delermine the horsepower saved by replacng the old pipewith a new 260mm plpe. Assume the value off as equat toNeglect osses of head except friction head

Given data: The diameter of the old pipe is D1=200 mm=0.2 m The length of the pipe is L=760 m The…

The water system in a suburban area consists of an old 200mm pipeline 760m long which conveys water from a pump to a reservoir whose water surface is 107m higher than the pump. Water is pumped at the rate of 0.07 m/s. Determine the horsepower saved by replacing the old pipe with a new 250mm pipe. Assume the value of f as equal to 0.033 and 0.022, respectively, for the dld and new pipes, Neglect bsses of head except friction head

The water system in a suburban area consists of an old 200mm pipeline 760m long which conveys water from a pump to a reservoir whose water surface is 107m higher than the pump. Water is pumped at the rate of 0.07 m/s. Determine the horsepower saved by replacing the old pipe with a new 250mm pipe. Assume the value of f as equal to 0.033 and 0.022, respectively, for the dld and new pipes, Neglect bsses of head except friction head

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
The pump in Fig. draws gasoline at 20 ° C from areservoir. Pumps are in big trouble if the liquid vaporizes(cavitates) before it enters the pump. ( a ) Neglecting lossesand assuming a fl ow rate of 65 gal/min, fi nd the limitationson ( x , y , z ) for avoiding cavitation. ( b ) If pipe frictionlosses are included, what additional limitations might beimportant?
A pump was installed with a suction head of 6 meter and a discharge head of 10 meters. The discharge rate of the pump is 60 liters per minute. What is the water horsepower of the pump?
A pump delivering 0.23 m3/s of water has a 304.8mm diameter suction flange and 254mm discharge flange. The suction pipe is 3.66m long and the discharge pipe is 22.86m long. Neglecting the turbulence losses in the pipe, find: a.) the head which the pump must deliver ( in meters ) b.) the motor power in KW required if the efficiency is 80%, c.) the reynold’s number and type of flow in the suction pipe d.) the reynold’s number and type of flow in the discharge pipe
A 70 percent efficient pump delivers water at 20°C fromone reservoir to another 20 ft higher, as in Fig. . Thepiping system consists of 60 ft of galvanized iron 2-in pipe,a reentrant entrance, two screwed 90° long-radius elbows,a screwed-open gate valve, and a sharp exit. What is theinput power required in horsepower with and without a 6°the well-designed conical expansion added to the exit? Theflow rate is 0.4 ft3/s.
A pump is needed to drain an excavation at a construction site. The excavation has alength of 50m, width of 50m, and a depth of 4m. The surface of the water in the excavation lies at adepth, H=3m, from the top the of the excavation. An old, radial flow, 1000W pump is immediatelyavailable for use; however, the total pump-motor efficiency, e, is only 50%. Estimate the drawdown inthe excavation in the first 4 hours of pumping. Neglect the change in H with increasing time. Neglectany head loss in the hose/pipe connected to the pump. (Hint: utilize the Pout equation, consider analternative definition of discharge as a change in volume over a change in time). Assume a specificweight of 9.79kN/m 3 .
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
A pipe 50 cm in diameter carries water (l0°C} at a rate of 0.5 m 3 / s. A pump in the pipe isused to move the water from an elevation of 30 m to 40 m. The pressure at section 1 is 70kPa gauge, and the pressure at section 2 is 350 kPa gauge. What power in kilowatts and inhorsepower must be supplied to the flow by the pump? Assume h L = 3 m of water and α 1 =α 2 = 1. Find the following Draw the Schematic diagram Drive the energy equation Calculate pump head Power requirement
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.
(a) the total dynamic head (TDH) in meters (b) the water power (WP) in kW (c) the pump mechanical efficiency (%) if the power input to the pump is 15hp
In a 225 mm pipeline 0.14 m3/s of water are pumped from a reservoir of surface elevation30 over a hill of elevation 50. A pump of what power is required to maintain a pressure of 345kPa on the hilltop if the head lost between reservoir and hilltop is 6 m?
A four-stage centrifugal pump has four identical impellers, keyed to the same shaft. The shaftis running at 400 r.p.m. and the total manometric head developed by the multistage pump is 40m. The discharge through the pump is 0.2 m*3/s. The vanes of each impeller are having outlet angle as 45°. If the width and diameter of each impeller at outlet is 5cm and 60 cm respectively, Find the manometric efficiency.