Water at 25 oC is pumped at a constant rate of 10 m3 /h from a large reservoir resting on the floor to the open top of an experimental absorption tower. The point of discharge 5 m above the floor, and friction losses in the 1-½-in. Schedule 40 steel pipe from the reservoir to the tower amount to 2.55 J/kg. At what height in the reservoir must the water level be kept if the pump can deliver only 0.1 kW?

Q: A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450 mm at…

A: Given data Specific gravity(SG) = 0.877 Diameter at section 1 = 150 mm Diameter at section 2 = 450…

Q: Water at 65 degrees Celsius is flowing horizontally at a rate of 84.1 m^3/hr in a pipe. It enters a…

A:

Q: A 20mm diameter commercial steel pipe, 30m long is used to drain an oil tank. Determine the…

A:

Q: For the water shooting out of the pipe and nozzle as shown in Fig. find 1- the flow rate (Q) through…

A: (1) To find: The flow rate through the pipe. Given: The diameter at A is DA=200 mm. The diameter at…

Q: What is the pressure at point 2 (kpa), if the water flows as irrotational inside the pipe? Given…

A:

Q: Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to…

A:

Q: Q1: A pipe connecting a reservoir to a turbine which discharges water to the down through another…

A:

Q: A reducing elbow is used to deflect and accelerate the flow of water from a horizontal pipe to 30 °…

A: Given: The pipe angle, θ = 30° The mass flow rate, m = 14 kg/s The cross-section area at inlet, A1 =…

Q: Doummate the power an 7- Water to run a Pelton wheel is supplied by a penstock of length e and…

A:

Q: Water with flow rate of 12 lps from ground level is delivered to upper levels using the 50-mm…

A: Given,  The water flow rate, Q = 12 L/s The diameter of pipe, d = 50 mm The angle between inlet and…

Q: A 50-mm diameter nozzle is attached to a 300-mm diameter pipe by flange bolts as shown. Assume that…

A: This problem is related to the flow measurement topic. the given diagram shows a conversing…

Q: The pumper truck shown in the figure below is to deliver 1.6 fts to a maximum elevation h of 61 ft…

A: To find : determine the power that the pump must add to the water. Given : flow rate Q=1.6 ft3/s…

Q: If the flow rate of water through the system shown is 0.050m/s under a total head loss of 9m,…

A: Given:C=120    n=0.020By Hazen-William equation for head loss:HL=10.094(QC)1.85*Ld4.87Put…

Q: 3. Three pipes of diameters 0.4m, 0.2m and 0.3m of lengths of 400m, 200m, and 300m, respectively,…

A:

Q: 4. The velocities of the fluid flowing on a pipe as shown in the figure is constant on the two…

A: Given data: V1=V2=1.2 m/s Need to determine the total head loss.

Q: Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to…

A:

Q: Water is pumped at the rate of 20 m3/s from the reservoir located at elevation 100 m and out through…

A: Water flow rate, Q=20 m3/sElevation of lower reservoir, z1=100 mSuction pipe diameter, ds=1.5…

Q: The water system in a suburban area consists of an old 200mm pipeline 760m long which conveys water…

A: Given data: The diameter of the old pipe is D1=200 mm=0.2 m The length of the pipe is L=760 m The…

Q: The horizontal pipe length is 180 m and the vertical pipe length is 24 m in the fire protection…

A: dear student please rate me postive :) Stay safe stay happy !   Data given -  L1 = 180 m  L2 = 24 m…

Q: Water from an open tank elevated 5m above ground is allowed to flow down to a pump. From the pump,…

A: Given that, Elvation of tank, z=5 m,length of pipe, l=100 m,Number of elbow, n=2,Volume flow rate,…

Q: The pump is used with a 3-in.-diameter hose to draw water from the cavity. Include frictional head…

A:

Q: Example the bottom and upper end respectively. The intensity of pressure at the bottom end is 350…

A: The entire mechanical energy of the flowing fluid, which includes the gravitational potential energy…

Q: Three parallel pipes connected at the two ends have flow-rates Q₁, Q2 and Q3 respectively, and the…

A:

Q: A 180 m of rubber cotton lined hose having a diameter of 75 mm is attached to a hydrant at which the…

A: Given: Pressure P1=410kPaFriction factor f=0.024Diameter of the hose D=0.075mDensity of water…

Q: Q5. Two pipes of diameters 400 mm, and 200 mm and lengths 300 m, and 150 m respectively are…

A: Pipe 1→d1=400mm   l1=300m     f1=0.03Pipe 2→d1=200mm   l1=150m     f1=0.034To determine flow rate of…

Q: The 150 mm pipeline as shown conducts water from a reservoir and discharges at a lower elevation…

A:

Q: Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to…

A:

Q: Situation 1 The 60 cm pipe conducts water from reservoir A to a pressure turbine which discharges…

A: Given:zA=70 mzB=0 mhl1=5v22ghl2=0.20v22gQ=0.7 m3/sd=60 cm

Q: Q. No 3). A water supply pipe line is designed to supplying water to a nearby city. Determine…

A: The relative roughness for commercial steel pipe is 0.045 × 10-3. Obtain the friction factor at…

Q: The power available at a stream flowing at 266 ft/s having a total head of 34 ft is

A: GIVEN DATA FLOW Q=266 ft3/sec HEAD H=34 ft   WE HAVE TO CALCULATE POWER

Q: Water must flow over a distance of 2 800 m from a large catchment dam to a turbine. The water level…

A: In parallel combination of pipes, their frictional head losses are the same but the power…

Q: In order to drain the tank faster, a pump is installed near the tank exit. Determine how much power…

A:

Q: A simple pitot tube and a piezometer are installed in a vertical pipe as shown in the figure. If…

A:

Q: Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to…

A: Write the given data. Q=9 m3/h=9 m3/h1 h3600 s=2.5×10-3 m3/sd=50 mmqL=2.5 J/kgP=0.1 kW=100 W

Q: A custom pipe connection was installed to deliver water to the highest level of a commercial…

A: given data; ⇒discharge at A (QA)=100lps=0.1m3/s⇒discharge at C(Qc)=40lps=0.04m3/s⇒discharge at B…

Q: A

A: Given that  volumetric flow rate of water (Q)= 741 L/s = 0.741 m3/s ;diameter of pipe coneecting A…

Q: A diverging tube discharges water from reservoir at a depth of 10 m below the water surface. The…

A:

Q: The water flow (T: with a diameter of D = 0.2 m has a head loss due to friction of hp 20°C) in an…

A: Answer: The volumetric flow rate of water through this pipe is 19.574 litre/sec.

Q: The 600 mm diameter pipe conducts water from reservoir A (El. 61 meters) to a pressure turbine (El.…

A: To given that D=600=0.6mhA-1=5×V22gh2-B=0.20×V22gQ=708/1000 m3/sQ=0.708m3/sPOUT=480hp consider the…

Q: Determine the rate of flow of water through a pipe of 300 mm diameter placed in an inclined position…

A:

Q: Which of the following equations below describes the system head of the piping shown below. The…

A:

Q: A horizontal pipe line 40 m long is connected to a water tank at one end and discharges freely into…

A:

Q: A 425 mm diameter pipe having 800 m length conveys water from high level tank to a point 22 m below…

A: We know that water is transported from a high-level tank to a place 22 metres below the water level…

Q: Water at 20°C is flowing through a horizontal nozzle at a flow rate of 0.005 m³/s. At the nozzle…

A: Given Data: Discharge rate, Q=0.005 m3/s Inlet diameter, d1=5 cm

Q: A sharp-edged orifice in the vertical wall of a large tank has a diameter of 25 mm. The coefficient…

A:

Q: The water system in a suburban area consists of an old 200mm pipeline 760m long which conveys water…

A:

Q: The 150 mm pipeline as shown conducts water from a reservoir and discharges at a lower elevation…

A:

Q: The 150 mm pipeline as shown conducts water from a reservoir and discharges at a lower elevation…

A:

Q: 1. The irrigation pump is used to supply water to the pond at B at a rate of 0.09 m3/s. If the pipe…

A: Given:Q=0.09 m3/sd=150 mmhl=0.1 m/m

Q: The 150 mm pipeline as shown conducts water from a reservoir and discharges at a lower elevation…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.