The wide-flange W10 x 15 (I= 68.9 in) cantilevered beam is made of A-36 steel (E = 29.0 (10³) ksi) and is subjected to the three loading conditions as shown in Figure 2. Using Methods of Superposition, determine the displacement, VB and slope, Os of the beam at its end point B. Note: Watch for units (1 ft. = 12 in.). A 3 kip/ft 6 ft El is constant 16 kip Figure 2 -6 ft 20 kip.ft B

The wide-flange W10 x 15 (I= 68.9 in) cantilevered beam is made of A-36 steel (E = 29.0 (10³) ksi) and is subjected to the three loading conditions as shown in Figure 2. Using Methods of Superposition, determine the displacement, VB and slope, Os of the beam at its end point B. Note: Watch for units (1 ft. = 12 in.). A 3 kip/ft 6 ft El is constant 16 kip Figure 2 -6 ft 20 kip.ft B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.9.7P: The cantilever beam A CB shown in the hgure is subjected to a uniform load of intensity q acting...

See similar textbooks

Similar questions

The cantilever beam A CB shown in the hgure is subjected to a uniform load of intensity q acting between points A and C. Determine the angle of rotation ÔAat the free end A>(Obtain the solution by using the modified form of Castigliano's theorem.)
The cantilever beam shown in the figure supports a triangularly distributed load of maximum intensity qü. Determine the deflection SBat the free end B. (Obtain the solution by determining the strain energy of the beam and then using Castigliano's theorem.)
An aluminum bar having a rectangular cross section (2.0 in. × 1.0 in.) and length L = 30 in. is compressed by axial loads that have a resultant P = 2800 lb acting at the midpoint of the long side of the cross section (sec figure). Assuming that the modulus of elasticity E is equal to 10 × 106 psi and that the ends of the bar are pinned, calculate the maximum deflection and the maximum bending moment Mmax.
Determine the plastic modulus Z and shape factor/for a W 12 x 14 wide-flange beam. Obtain the cross-sectional dimensions and section modulus of the beam from Table F-l(a) in Appendix F.
A simple beam AB of length L and height h (see figure) is heated in such a manner that the temperature difference 7= T{between the bottom and top of the beam is proportional to the distance from support A: that is, assume the temperature difference varies linearly along the beam: T2- Tt= Tax in which 7"0 is a constant having units of temperature (degrees) per unit distance. Determine the maximum deflection SW9Xof the beam, Repeat for a quadratic temperature variation along the beam, so T2+T1= Tax
Question 1) F=11 kN single load, M=22 kN.m moment andA distributed load of w=5 kN/m is effective. The length L is also given as L=5 m.The cross-sectional properties of the beam are; body height Hg=218 mm, body thickness xg=18 mm, flangewidth xf=190 mm, flange height yF13 mm. Point E on the section is flange-It is located just below the body junction. In the section taken from the B line of the beamIt is desired to determine the stress state. According to this;Question 1-A) Find the support response (DY) at point D. (Return your result in kNQuestion 1-B) Find the support response (Ay) at point A. (Return your result in kNwrite.)Question 1-C) Find the shear force (VB) at point B. (KN your resulttype in size.)
determine the deflection at B in mm using Conjugate Beam Method. Consider 150 mm x 200 (b x h) mm section and E=80 GPa. Enter the absolute value only and round off your answer to 3 decimal places Answer asap. I rate
(1a) A simply supported beam of hollow circular section of external diameter 200mm, and internal diameter 150mm has a span of 6m. It is subjected to concentrated load of 50kN and Udl of 5kN/m over the entire span. Determine the maximum slope at the support and maximum deflection at centre. Take E = 2 x 105N/mm2 (1b)Explain the following terminology: The strain Stress Young modulus in the column. Rigid Prop
The beam safely supports shear forces and bending moments of 2kN and 6.5 kN-m respectively. Based on this criterion, can it be safely subjected to the loads F = 1kN and C = 1.6 kN-m? Use the area method
Given the 200mm x 400mm beam with the loading shown, determine: a. the amount of load P applied on the beam if the deflection on the midspan is 5 mm downward. b. by this same load P, what is the deflection and slope on the beam at point D? Set the parameters as a = 3m, L = 9m , E = 200 GPa. EI is constant.
Two elastic beams with equal bending rigidity of EI are connected by a pin at B. The beam is fixed at A and a roller support is attached at C. Beam BC is subjected to a uniformly distributed load of magnitude w=1 N/m. If the bending rigidity EI is 108Nmm2, determine a) the lateral deflection at B, b) the rotational angle at B, c) the rotational angle at C. d) sketch the deformed shape
In the beam, which is given the loading and supporting status below a) Find the location of the largest crash and the value of the crash. b) What is the maximum length of the beam (L) so that the largest collapse value is less than 1.5 mm? E = 210 GPa Mo = 250 kNm I = 556x10-6 m4