The work table of a positioning system is driven by a leadscrew whose pitch =6 mm. the lead screw is connected to the output shaft of a stepper motor though a gear box whose ratio is 4:1. The stepper motor has 45 step angles. The table must move a distance of 200 mm its present position at a linear velocity = 400 mm/min. Determine a. how many pulses are required to move the table the specified distance and b. The required motor speed and pulse rate to achieve the desired table velocity.

The work table of a positioning system is driven by a leadscrew whose pitch =6 mm. the lead screw is connected to the output shaft of a stepper motor though a gear box whose ratio is 4:1. The stepper motor has 45 step angles. The table must move a distance of 200 mm its present position at a linear velocity = 400 mm/min. Determine a. how many pulses are required to move the table the specified distance and b. The required motor speed and pulse rate to achieve the desired table velocity.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A NC machine tool table is powered by a servomotor, lead screw, and optical encoder. The lead screw has a pitch = 5.0 mm and is connected to the motor shaft with a gear ratio of 16:1 (16 turns of the motor for each turn of the lead screw). The optical encoder is connected directly to the lead screw and generates 200 pulses/rev of the lead screw. The table must move a distance = 100 mm at a feed rate = 500 mm/min. Determine (a) the pulse count received by the control system to verify that the table has moved exactly 100 mm; and (b) the pulse rate and (c) motor speed that correspond to the feed rate of 500 mm/min. Solve the problem assuming the optical encoder is directly coupled to the motor shaft rather than to the lead screw.
A CNC machine tool table is powered by a servomotor, ball screw, and optical encoder. The ball screw has a pitch = 7.5 mm and is connected to the motor shaft with a gear ratio of 12:1. The optical encoder is connected to the ball screw and generates 200 pulses/rev of the screw. The table must move a distance of 300 mm at a feed rate = 450 mm/min. (a) Determine the pulse count received by the control system to verify that the table has moved exactly 300 mm. Also, what are (b) the pulse rate and (c) motor speed that corresponds to the specified feed rate?
1. If a rotating machine is rotated at 300 rpm in the balancing machine and the maximum value of the excitation force due to the unbalanced mass appears 0.05s later than the reference pulse, where is the unbalanced mass?
A device with a mass of 1000 kg is placed on top of the suspension, whereby the springs are compressed into a pile a distance of 4 mm. What is the system specific angle frequency (rad / s) to one decimal place?
Determine the system's personal frequency equation
If one node is observed at a frequency of 1000 RPM, during a whiring of a simply supported long slender rotating shaft. The first critical speed of the shaft in RPM is ______?
Two identical 2000 kW alternator operates in parallel. The governor of the first machine is such that the frequency drops uniformly from 50 Hz at no-load to 48 Hz at full-load. The corresponding uniform speed drop of the second machine is 50 Hz to 47.5 Hz, What is the maximum load that can be delivered without overloading either machine?
Find natural frequency
6.1) Obtain a kinematic diagram (schematic view) equivalent to the following mechanisms and their degree of freedom.
One end of a light uniform rod is attached to a wall by africtionless hinge. The rod is held in a horizontal position by a wire thatruns from the other end of the rod to the wall. The wire has length 2.00 mand makes an angle of 30.0° with the rod. A block with mass m is suspendedby a light rope attached to the middle of the rod. The transversefundamental standing wave on the wire has frequency f. The mass m isvaried and for each value the frequency is measured. You plot f 2 versus mand find that your data lie close to a straight line with slope 20.4 kg -1 # s-2.What is the mass of the wire? Assume that the change in the length of thewire when the tension changes is small enough to neglect.
The response of a system is given by xt=0.003cos 30t +0.004sin 30t m. Determine (a) the amplitude of motion, (b) the period of motion, (c) the frequency in Hz, (d) the frequency in rad/s, (e) the frequency in rpm, (f) the phase angle, and (g) the response in the form of xt=Asin (ωt+φ)
4. The system has three axes or three levels, only the motor is connected on the first axis. At the end of axis 1 is a gear (N₁) connected to a gear (N₂), the left gear of Axis 2. The right gear of axis 2 (N3) is connected to the gear (N4), the left gear of Axis 3. At Axis 3 has an inertia (Ja) of 8 kg-m² and a damper of 32 N-m-s/rad. Draw the system and find the Transfer function that relates the voltage at the motor to the angular displacement at JA. Additional information: Gear N₁ has 10 teeth and an inertia of 1.5 kg-m² Gear N₂ has 20 teeth and an inertia of 2 kg-m² Gear N3 has 10 teeth and an inertia of 2 kg-m² Gear N4 has 20 teeth