Three interconnected cylindrical members are subjected to axial loads as shown below. If the allowable axial stresses are 140 MPa in the steel, 75 MPa in the brass, and 90 MPa in the aluminum, determine the required diameters of each the cylindrical bars. B Brass Aluminum D Steel 270 kN 245 kN 200 kN -225 kN 0.5 m 0.5 m 0.5 m

Three interconnected cylindrical members are subjected to axial loads as shown below. If the allowable axial stresses are 140 MPa in the steel, 75 MPa in the brass, and 90 MPa in the aluminum, determine the required diameters of each the cylindrical bars. B Brass Aluminum D Steel 270 kN 245 kN 200 kN -225 kN 0.5 m 0.5 m 0.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 53 kN if it developed a stress of 52 MPa. Take note that the inner diameter is 2/6 of the outer diameter. Hiiii i am having a hard time. It is kinda urgent tysm i appreciate u sm
A uniform cross section rod is composed of an aluminum section rigidly attached between steel and bronze sections. Axial loads are applied at the positions indicated.If P = 5.8 kN and the allowable stresses on the steel, aluminum and bronze are 40 MPa, 30 MPa and 25 MPa, respectively. Determine the minimum safe diameter for the rod. Answer: d= ___________________
The shaft assembly is made from a steel tube 1 in. in diameter,which is bonded to a solid brass core 0.5 in. in diameter. If atorque of 250 lb-ft is applied at its end, determine the maximumshear stress in psi experienced by the assembly. Take G for steelat 11.4x103 ksi and G brass at 5.2 x 103 ksi.
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 556 mm2 and P= 36.79 kN. Round off the final answer to four decimal places.
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
A 14 mm diameter rivet joins the plates that are each 1.10 m wide. The allowable stresses are 120 000 KPa for bearing in the plate material and 60 000 KPa for shearing rivet. Determine the minimum thickness of each plate and the largest average tensile stress in the plates
A mechanical coupling connects a solid shaft with a diameter of 80 mm and a hollow shaft with external and internal diameters of 100 Y and 85 mm, respectively. The allowable stress for the solid shaft is 55 MPa and for the hollow shaft, 60 MPa. The coupling initially consists of a series of 8 aluminum bolts [( tau aluminum ) adm =40 MPayG aluminum =28 GPa] of 12 mm diameter located in a circumference of 250 mm diameter. Determine a) the radius at which an additional series of steel bolts [( tau steel ) adm =60 MPa and G steel =83 GPa] of 8 mm diameter must be placed to support the maximum allowable torque, b) the number of steel bolts necessary to support the specified torque and c) the power of a motor that can transmit that torque by turning the array at 1.25 rev/s
A cylinder having an internal diameter of 20 in and an external diameter of 36 in is subjected to an internal pressure of 10000 psi and an external pressure of 2500 psi. Determine the hoop stress at the inner surface of the cylinder in psi.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter required for rod 1. Assume P = 80 kN and Q = 140 kN. Express your answer in mm rounded to the nearest hundredths.
A steel pipe with an outer diameter of 50 mm and a wall thickness of 5 mm is subjected to aninternal pressure of 10 MPa and an axial load of 20 kN at an angle of 45 degrees to the axis of thepipe. Determine the maximum axial stress and maximum hoop stress developed in the pipe.
A cylinder having an internal diameter of 22 in. and an external diameter of 38 in. is subjected to an internal pressure of 12,000 psi and an external pressure of 2300 psi. Determine the hoop stress at the inner and outer surface of the cylinder. d.14,789 psi and 6,879 psi c.13, 143 psi and 5,143 psi b.15,876 psi and 8,366 psi a.17,181 psi and 7,481 psi