Axial loads are Bronze Aluminum Steel applied to the compound rod that is composed of an aluminum A=400 mm² A=600 mm² A=300 mm² 2P ЗР 4P -3 m →+ 5 m - - 4 m segment rigidly connected between steel and bronze segments. If P = 75 kN, determine the following: a. Stress in the bronze segment. b. Stress in the aluminum segment. c. Stress in the steel segment.

Axial loads are Bronze Aluminum Steel applied to the compound rod that is composed of an aluminum A=400 mm² A=600 mm² A=300 mm² 2P ЗР 4P -3 m →+ 5 m - - 4 m segment rigidly connected between steel and bronze segments. If P = 75 kN, determine the following: a. Stress in the bronze segment. b. Stress in the aluminum segment. c. Stress in the steel segment.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
A column has an outside diameter, D = 550 mm, an inner diameter, d = 150 mm.Determine the average normal stress developed on the cross section if the load, F is1890 kN.
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20o Properties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2 L = 2.75 m
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 3950 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 2900 mm2 and an allowable normal stress of 160 MPa. Assume x1 = 2.0 m, x2 = 3.0 m, y1 = 0.8 m, and y2 = 2.8 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
2. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determinethe outside diameter of the tube if the stress is limited to 120 MN/m2.
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20oProperties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2
The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is w = 70 mm and the bar thickness is 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 115 MPa, the bearing stress in the bar cannot exceed 140 MPa, and the bearing stress in the bracket cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure.
A steel bar ABCD consists of three sections: AB is of 20 mm diameter and 200 mm long, BC is 25 mm square and 400 mm long, and CD is of 12 mm diameter and 200 mm long. The bar is subjected to an axial compressive load which induces a stress of 30 MN/m 2 on the largest cross-section. Determine the total decrease in the length of the bar when the load is applied. For steel E -- 210GN/m 2. [0.272 mm.] Could you please answer this fully? If you use * can you explain whatyou mean by it. Thank you
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4850 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 4750 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 2.2 m, x2 = 3.4 m, y1 = 1.1 m, and y2 = 2.7 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.Answer: Pmax = Enter your answer in accordance to the question statement kN