A Bys Find the reactions. Fill in the blank's. 8k a 4' 6' 6. FBD

Q: you s < showing how you de

A:

Q: Find others Force applied =2.78N Area = 1mm?

A: Given data : Force=F Area=A   Required : Stress

Q: B and the 0.5-in

A:

Q: what  is the tension on the rope? also pls show solution clear

A:

Q: centr the the special case 2 -a) 20h

A: Given data Geometry is given Required Y bar

Q: using simpsons (3/8 Yule , eualuate taking (6) strips. Q-3-

A: Given ,  the function -  ∫01dx1+x use of simpsons 3/8 th rule.  no. of strips to be taken 6.…

Q: уы =3 bafel beared Find the

A: Given data : Modulus of elasticity=E Bulk modulus=K   Required : Poisson ratio

Q: for part a , b c only

A:

Q: Ag. Bys Find the reactions. Fill in the blank's. 8k. a 4' 6' 6. FBD Final FBD

A:

Q: Find bending moment

A: Given; A concentrated load P acts on a simply supported beamof span L at a distance L/3 from the…

Q: ss of 1.5 tons and ction between the

A:

Q: A frame is being raised on a pivot point. a crane lifts the frame and shows 315 165 at 45⁰. How much…

A:

Q: a load ir incraasadta

A:

Q: the load, what happorns Afler releasing the longth and width ok the wire

A: we have to calculate stress strain elongation , lateral strain.

Q: Q3/ Choose the correct answer and explain why?

A: 1). The ability of material to withstand the tensile force befor it break It's called as tensile…

Q: metaicfhread: Pitch- 3mm thocadaryle=65 using 3-wire meltad Best size wisre diametoe ?

A:

Q: 50 lb A 3 in. C B D 4 in.- -6 in.-

A:

Q: 4y" + y = 0,

A: Dear Student  as per bartleby guidelines I am allowed to answer first question only . Please post…

Q: What is the vertical reaction at A? answer in kips

A:

Q: mine the stre t B. Then dr

A:

Q: y of holding metal in the vice whe

A: Required  correct method for holding metal in the vice

Q: ..Shakespeare write Hamlet? а. did b. was С. had d. is

A: Given Fill in the blanks To find Appropriate word suitable for the question

Q: Deive equabon for height Rof Pate Governer useig Instantenous Centre Method.

A:

Q: Find the support reactions

A:

Q: Find a) Сp, Cv

A:

Q: Write the flexure formula?

A: Flexure formula This formula is used to determine the internal bending stress when an external force…

Q: 5 ft 5 ft 12 ft 5 ft reactions in A and D

A:

Q: ngth Land flexura Gon of the free en

A:

Q: a fillet w eld is 5 r jual to: )14.14 r

A: given:length of weld l=5mm

Q: Choose three types of Reuleaux lower pairs, and answer the following, F.1 Write down their names?…

A:

Q: of the block if 60 °F (C

A: given:μ=0.76N/sm2m=10kgθ=200y=0.1mm

Q: Irent (do

A:

Q: figure below. Show that a c

A:

Q: 2 Find T: For q=-KA when dr

A:

Q: Find the degrees of freedom using grueblers equation

A:

Q: D.5m/s) find the (H).

A: To find H

Q: ith both ends open is 0.85 m long. Assumin

A: f3=600Hz

Q: Use the method of sections or joins and please say if it's tension or compression at HC only.

A:

Q: Describe the steps how to solve all reaction at the support

A: The diagram of truss is given as,

Q: Find the tensien force in each 35 eable. A

A:

Q: below? [5]

A:

Q: wad At0 B70 that: A/D 4. IF AxB -0 plove.

A: Given data: A→×B→=0A→=0B→=0 Need to prove A→//B→

Q: I attached the question

A: Given Data Film thickness is: y=1 mm=1×10-3 m The diameter of the shaft is: d=0.5 m The speed of…

Q: which of the following law(s) should be satisfied?

A: Given, Fluid enters at point 1 and exit from point 2 and 3.

Q: between Hthe n in each Strin 14.2K.

A: Let T1 and T2 are the tension in strings 1 and 2 g= acceleration die to gravity=10m/s2

Q: e. Find the minimum diameter of the wire

A: for safe design stress induced in the rod should be less than or equal to the yield stress. so apply…

Q: rad/sec and having 20 te sure angle is 20° and m. on at the centre of the sha

A:

Q: What is the Vertical Reaction at B in kips

A: The provided beam is an indeterminate beam since the number of reactions are more than the number of…

Q: ht, what is the tension in the wire?

A: To find tension ( T)