Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued on the contact surfaces. The glue to be used can safely provide a shear strength of 110 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 12 kips. Note that a gap of 0.5 in. is required between boards (1) and (2). P L 6 in. (1) 0.5 in.- (2)

Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued on the contact surfaces. The glue to be used can safely provide a shear strength of 110 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 12 kips. Note that a gap of 0.5 in. is required between boards (1) and (2). P L 6 in. (1) 0.5 in.- (2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

THe bracket shown is made of cold drawn steel with Sy=400MPa and Su=480 MPa, and is fastened to a beam made of the same material by five rivets that are made of a steel with Sy=300 MPa and Sut=365 MPa. The thickness of the bracket and the beam are 12 mm and 16 mm respectively.Diameters of the rivets are 20 mm. What safe load F(steady) can be supported by the riveted joint for a factor of safety of 2. Use distortion energy theory of failure.
A laminated wood beam consists of eight 2.25 in. × 5.00-in. planks glued together to form a section b = 5.00 in. wide by d = 18 in. deep, as shown. If the allowable strength of the glue in shear is 105 psi, determine(a) the maximum uniformly distributed load w that can be applied over the full length of the beam if the beam is simply supported and has a span of L = 19 ft. [Answer: w = 663.2 lb/ft]
All pins are in double shear, each has a diameter of 13mm, and the average shear stress in each pin is not to exceed 65 MPa. Determine the maximum magnitude P of the loads that the beam can support
The rivet group connects two narrow lengths of plate, one of which carries a 15 kN load. If the ultimate shear strength t of a rivet is 350 N/mm² and its failure strength in compression stress is 600 N/mm², determine the minimum allowable values of rivet diameter d (mm) and plate thickness t (mm).
The five-bolt connection shown must support an applied load of P = 214 kN. If the average shear stress in the bolts must be limited to 249 MPa, determine the minimum bolt diameter that may be used in the connection.
The plate shown is made of UNS G10350 cold drawn steel (Sy=460 MPa and Su=550 MPa),and is fastened to an I beam made of UNS G10150 cold drawn steel (Sy=320 MPa and Su=385 MPa) by four rivets made of a steel with Sy=300 MPa and Su=365 MPa. Thickness of the plate is 10 mm and thickness of the flanges of the I beam is 15 mm. Diameter of the rivets is 20 mm. What safe load F (steady) can be supported by the riveted joint for a factor of safety of 2. Use distortion energy theory of failure.
' Three piates are joined with a 12-mm diameter pin as shown beiow. Determine the maximum load p that can be transmitted by the joint if the maximum bearing stress between a plate and the pin must be limited to 650 MPa .
The lap joint is fastened by 20 mm rivets placed alongside each other as shown along the length of the plate. Determine the safety of the lap joint to carry an axial load P=180 KN if the shearing stress in the rivets is limited to 60 MPa, the bearing stress in the plates to 110 MPa, and the average tensile stress in the plate is limited to 140 MPa. Plate width, W=140 mm, splice plate thickness, t=15 mm and main plate thickness, t = 40 mm. P = 180 KN
A steel rod of 30 mm diameter is enclosed centrally in a hollow copper tube of external diameter 40 mm and 5 mm thick. The composite bar is then subjected to an axial pull of 45 kN. If the length of the compound rod is 150 mm , and the elasticity moduli are Est = 200 GPa and Ecu = 100 GPa , determine: 1.2.2 The load carried by the rod and that carried by the tube
A piping tube with an outside diameter of 50 mm and wall thickness of 5 mm is used as a compression member. Determine the maximum load P that the member can support if the normal stress in the member must be limited to 120 MPa.
The outside diameter of the steel pipe shown is 220 mm and its wall thickness is 6.0 mm. The upper bearing plate has the same width as the reinforced concrete beam it supports. The total load on the column by the reinforced concrete beam is 550 kN. Determine: A. The length L of the rectangular upper bearing plate if its width is 275 mm. and the average bearing stress between the steel plate and the reinforced concrete beam is not to exceed 6.2 MPa.
A thrust collar that rests on a 0.75 in thick polymer plate supports the vertical nylon shaft shown below. The shaft has a diameter d = 0.50 in. The load acting acting on the shaft is P = 600lb. A) The ultimate shear strength of the nylon shaft is 2700 psi, and a factor of safety of 2.5 with respect to shear is required. Determine the minimum thickness t required for the thrust collar B) The ultimate bearing strength of the polymer plate is 2000 psi, and a factor of safety of 3.0 with respect to bearing is required. Determine the minimum outer diameter Dcollar required for the thrust collar.