Two forkend pieces are to be joined together by a single steel pin of 25mm diameter and they are required to transmit 50 kN. Determine the minimum crosssectional area of material required in one branch of either fork if the stress in the fork material is not to exceed 180 MN/m2 . What will be the maximum shear stress in the pin?

Q: A rod composed of an aluminum section rigidly attached between steel and bronze section. Axial loads…

A: Given data as per the question  P=3000 lb  Area of rod =0.5 in2

Q: Determine the width w of the plate loaded as shown if the permissible stress in plates of joints…

A: Given data,  σ = 200MPa.= 200 N/mm2  Pin dimension is d= 10 mm  P= 2000 N  Thickness t= 2mm

Q: A thin-walled cylinder has an internal diameter of 1200 mm and has walls 1.2 mm thick. It is…

A: For solution refer below images.

Q: The cross-sectional area of each member of the truss is 42 cm2. в L. C E 6m 100 kN 300 kN Determine…

A:

Q: Q. A cantilever, 2.5 m long carries a UDL of 20 kN/m. The breadth of the section remains constant…

A:

Q: Two ropes are used to hoist a 610 Ib engine/transmission assembly as shown. The rope is anchored at…

A: Since we only answer up to 3 sub parts. We will answer first 3. Please resubmit the question and…

Q: For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to…

A:

Q: A 150-mm-long bronze tube, closed at its ends, is 80 mm in diameter and has a wall thickness of 3mm.…

A:

Q: View Policies Current Attempt in Progress Two solid cylindrical rods (1) and (2) are joined together…

A:

Q: 10. The plate welded to the end of the l-beam is fastened to the support with four 10-mm-diameter…

A: Given: d = 10 mm             P = 30 kN To determine: Normal stress & Shear stress Concept:…

Q: The cross-sectional area of bar ABCD is 600 mm?. Determine the maximum normal stress in the bar.…

A: Given data: Force acting at B = 25kN Force acting at C = -20kN Force acting at D = 30kN Cross…

Q: A solid 30-mm-diameter shaft is used in an aircraft engine to transmit 86 kW at 1,250 rpm to a…

A: we have to develop principal stress & shear stress

Q: The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is…

A:

Q: For P =100 kN, determine the minimum plate thickness t required if the allowable stress is 125 MP

A: Consider the hole A, The radius of the hole is given as, The width of fillet A is given as, Width…

Q: Three identical plates of 62 mm wide and 7 mm thick connected by a square pin with side dimension 12…

A:

Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together. Find the smallest thickness of each…

A: The stress acting between two bodies when they are in contact to each other. It can be called as…

Q: For the connection shown, the average shear stress in the 11-mm-diameter bolts must be limited to…

A:

Q: 1. A water tank 3 m in diameter and 6 m high is made from a steel with thickness of 10 mm. a) When…

A:

Q: A flanged bolt coupling consists of eight 10-mm diameter steel bolts on a bolt circle 400 mm in…

A: Given:no=8do=10 mmDo=400 mmni=6di=10 mmDi=300 mmFo=8000 N

Q: A motor boat engine shaft is coupled to the propeller shaft of diameter 30mm. If the allowable shear…

A: Given, Allowable shear stress, τ=43 MPa=43 N/mm2 The diameter of the shaft, d=30 mm

Q: For the connection shown, the bolt diameter is d = 30 mm.  The average shear stress in the bolts…

A:

Q: A thin hollow sphere of radius 300 mm and thickness 2.5 m is subjected to an internal pressure.…

A: Thin spherical shell is given Tensile stress in sphere =  σ = 360 kPa Radius of sphere = r = 300 mm…

Q: For the connection shown, the bolt diameter is d = 20 mm. The average shear stress in the bolts must…

A:

Q: A spherical pressure vessel of 5.7 meter diameter is subjected to an internal pressure of 3.8 MPa.…

A: Given data  d=5.7 mP=3.8 MPat=5 mm Here, d is the diameter, P is the pressure on the vessel.  Now we…

Q: An aluminum [E = 10100 ksi] control rod with a circular cross section must not stretch more than…

A:

Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each…

A:

Q: For the connection shown, the average shear stress in the 6-mm-diameter bolts must be limited to 176…

A:

Q: A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of…

A: Given: Diameter of the reinforced concrete column→D=400 mm So total area of the…

Q: Q.3. A steel rod of 20-mm diameter passes through a 0.8-m long brass tube of 35-mm external diameter…

A:

Q: QUESTION 2 с Y The 6.7-in diameter steel shaft AB is attached into the rigid wall at C and supported…

A: Given data: ◆ The dia meter of the shaft: d = 6.7 in ◆ The length of the lever AC: x = 3.54 ft ◆ The…

Q: Rigid bar ABC supports a weight of W 50 kN. Bar ABC is pinned at A and supported at B by rod (1),…

A:

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 17…

A:

Q: QUESTION 1. Determine the constant thickness t of the square shaped tube if the average shear stress…

A: Given data: The average shear stress is; ? = 90 MPa. The magnitude of the torque is; T = 3 kNm. The…

Q: The rectangular bar is connected to the support bracket with a 19-mm-diameter pin. The bar width is…

A:

Q: If the failure of shearing stress in a steel plate is 2,300KN, determine (a) the force required to…

A:

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side…

A:

Q: A line shaft rotating at 200 rpm is to transmit 20 kW. The allowable shear stress fo the material of…

A:

Q: Two aluminum plates, each having a width of b = 8.0 in. and a thickness of t = 0.750 in., are welded…

A:

Q: Q3) A pillar crane, shown in below, is fastened to the foundation by means of 16 identical bolts…

A:

Q: With the same given, if the members have a square cross-section with a diagonal of 11.31 cm and…

A: In the question, the applied magnitude of force is not given, thus it is not possible to calculate…

Q: Two identical plates of 63 mm wide and 5 mm thick is connected by a square pin with side dimension…

A:

Q: Determine the required thickness of member BC to the nearest in., and the diameter of the pins at A…

A:

Q: Determine the thickness of a steel air receiver with 30 in. diameter and pressure load of 120 psi,…

A:

Q: Two fork end pieces are to be joined together by a single steel pin of 25mm diameter and they are…

A:

Q: The steel bar shown has a 100 mm by 25 mm rectangular cross section. If an axial force of P = 180 kN…

A:

Q: Determine the stress in each cord for the system shown in fig. below, if the cross section area of…

A: GIVEN DATA- A CORD SYSTEM WITH FORCES GIVEN IN FIGURE WE HAVE TO FIND STRESS IN EACH CORD

Q: Determine how many 14mm bolts should be used to attach a cap to a cylindrical tank with a diameter…

A:

Q: As shown in the picture below, the sloping direction of the member is subjected to a compression of…

A: given:

Q: Q. 6: A steel rod 20 mm in diameter, 400 mm long is co-axially enclosed in brass tube of 25 mm…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.