Two strain gages are mounted on a thin-walled cylindrical pressure vessel. One strain gage is oriented parallel to the longitudinal axis of the thin-walled cylindrical pressure vessel while the other strain gage is perpendicular to the first. The tank has radius r = 20 in. and wall thickness of t =0.4 in. It is made from a material that has Young's Modulus E = 15x10 psi and Poisson's Ratio v = 0.31. The strain gages %3D %3D in. in. report the following after the tank is pressurized: & = 133.0u: and & = 591.5µ- in. %3D in. E (ɛ + v&H) and (1–v²) From Hooke's Law: o, = (1– v²) Determine: Gage Pressurep.

Two strain gages are mounted on a thin-walled cylindrical pressure vessel. One strain gage is oriented parallel to the longitudinal axis of the thin-walled cylindrical pressure vessel while the other strain gage is perpendicular to the first. The tank has radius r = 20 in. and wall thickness of t =0.4 in. It is made from a material that has Young's Modulus E = 15x10 psi and Poisson's Ratio v = 0.31. The strain gages %3D %3D in. in. report the following after the tank is pressurized: & = 133.0u: and & = 591.5µ- in. %3D in. E (ɛ + v&H) and (1–v²) From Hooke's Law: o, = (1– v²) Determine: Gage Pressurep.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the hoop stress on a cylindrical pressure vessel with diameter d, thickness t and gauge pressure p is 58.54 MPa, then the longitudinal stress must be equal to (in MPa)...
A closed cylindrical tank, placed horizontally, 410 mm in internal diameter and 2.0 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure.a. What is the magnitude of the internal pressure in MPa? b. What is the applied axial force in kN?
A closed cylindrical tank containing a pressurized fluid has an inside diameter of 510 mm and a wall thickness of 10 mm. The tank is pressurized to 2.40 MPa. Determine the longitudinal stress in the wall of the tank.
Find the stresses in a medium with a cylindrical hole under the action of radial tension or compression by the stress oo and the internal pressure p. Determine the stress concen tration coefficient. How does the stress concentration coefficient and stress distribution depend on the radius of the cavity?
QUESTION 5 The solid shaft as shown in Figure 5 is made of material that has an allowable stress of 275 MPa. Determine the required diameter of the shaft to the nearest mm.
The 4000 mm long eyebar BC shown in the figure has an outside dimension of 80mm x 40mm and a uniform thickness of 7mm. length of AB = 2.5m a. Calculate the maximum value of W if normal stress in BC is 30 mPab. If W is 100 kN, what is the stress at AB with 200mm2 cross sectional area
The thin-walled tube is subjected to an axial force of 40kN. If the tube elongates 4mm and its circumference decreases 0.09 mm, determine the modulus of elasticity, Poisson's ratio, and the shear modulus of the tubers material. The material behaves elastically.
A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be replaced by a solid circular bar. a) Determine the required diameter of bar so that the maximum shear stress in the bar will not exceed the maximum shear stress in the tube. b) If the computed value of diameter in the previous question increase by 15%, what is the new shear stress of the circular bar? c) Determine the angle of twist in degrees of the tube if the length of the tube is 1m and the shear modulus is 80 GPa. Use T=14 kN-m.
When filled to capacity, the unpressurized storage tank shown contains water to a height of h = 19 ft. The outside diameter of the tank is 8 ft and the wall thickness is 0.625 in. Determine the maximum normal stress at the base of the tank. (Weight density of water = 62.4 lb/ft3) 405 psi 588 psi 793 psi 624 psi 746 psi
5 decimal places 1. At the proportional limit, a certain material has a stress of 78 MPa as the strain is 0.0004. What is the modulus of elasticity of the material in GPa? 2. A 7-ft diameter spherical tank is subjected to an internal pressure of 24 psf. If the wall thickness is 0.35", determine the tangential stress of the wall in psi. A spherical pressure vessel of 5.7 meter diameter is subjected to an internal pressure of 5.0 MPa. Determine the tangential stress (MPa) developed in the wall of the vessel if the thickness is 4 mm.
At a point in a stressed material, the major principal stress is 180 kPa compression and the minor principal stress is 40 kPa tension. (a) Determine the Mohr’s circle for this stress combination. (b) What is the maximum shear stress that acts at the point, and what is the value for the normal stress acting on the plane of maximum shear? (c) Determine the value of the normal and shear stress acting on the plane 22.5° ccw from the major principal plane.
If the block is subjected to the centrally applied force of 600kN, determine the average normal stress in the material. Show the stress acting on a differential volume element of the material