Use the battery discharge curves below. If the battery is discharged at a constant rate of 240 mA until the battery reaches a voltage of 5.7 volts, what will be its AH rating in this application. Assume the battery is completely discharged at this voltage. See your email for the figure. O a. 320 mAH O b. 600 mAH OC. 400 mAH O d. 180 mAH O e. 160 mAH

Use the battery discharge curves below. If the battery is discharged at a constant rate of 240 mA until the battery reaches a voltage of 5.7 volts, what will be its AH rating in this application. Assume the battery is completely discharged at this voltage. See your email for the figure. O a. 320 mAH O b. 600 mAH OC. 400 mAH O d. 180 mAH O e. 160 mAH

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter2: Basic Electricity

Section: Chapter Questions

Problem 21RQ: Describe briefly the method a dry cell battery uses to produce voltage.

See similar textbooks

Similar questions

1) This MCQ QUESTION FROM BASIC POWER ELECTRICAL ENGINEERING course. just write for me the the correct answer.
q25/a Write the features of Air circuit breaker and mention its application.
1.) An incandescent lamp, rated at 100 watts, gives a certain amount of light when placed across the 120V ac power line. Would the amount of light increase, decrease or remain the same, when the lamp is placed across a 120V dc power line? Discuss. 2.) Explain what is meant by effective current and effective voltage.
For a battery with a rated voltage = 12 V and a rated capacity = 350 A-h, determinea. The rated chemical energy stored in thebattery.b. The total charge that can be supplied at the ratedvoltage.
h. What is the dc power dissipated by the device at the operating point?i. What is the power supplied by VCC ?j. Determine the power dissipated by the resistive elements by taking the difference betweenthe results of parts (h) and (i).
Create an explantion explaining the working operation of the circuit below.
Suppose we include the lead resistance in the calculation of temperature for a class A RTD. If R3 = 1000 ohms, Ra = 18 ohms, V0 = 1.80 volts, and V = 5 volts. Including the tolerances, what is the highest temperature you could measure in °C? (Type in a two-decimal number)
A PMMC instrument has internal resistance of 0.8 kΩ and gives full scale deflection for 33 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 75 V will be __________________ ohms. a. 226.47 b. -360.00 c. 1472.73 d. 93717.00
Current is the flow of charges in a directed path. When we connect yourmobile phone charger to the sockets in your various homes, charges startflowing through. Describe into details where these charges are generatedfrom and the processes involved.
Solve the following Numerical problems a. What is the Output Voltage of a battery that expends 7.2J of energy in moving 1C of charge? b. A 50-ohm load dissipates 200W of power. How much is the voltage and current across the load? c. If one branch of a 120-V power line is protected by a fuse of 20-A. Will the fuse carry 10-Ohm load? d. If total resistance of a series circuit is 280-Ohm. If one of the resistance is 160-Ohm. What is the sum of other two resistances?
Give a brief introduction about the topic of generation and measurement of direct current voltage...(if possible for 2 pg or 1 pg) high voltage engineering subject..
Electrical power (P) is given by P = E²/R, where is voltage and R is resistance. Approximate the maximum percent error in calculating power if 120 volts is applied to 2000- ohm resistor and the possible percent errors in measuring E and R are 3% and 4%, respectively.