Using Mohr's Circle, solve Review problem R9-5 in the 10th Ed. of the text. Plot your solution along with notation of the axes and all the values below on graph paper. Show your calculation for the values below. 1. Find the Principal Stresses, and the orientation of the element at the those stresses 2. Find the maximum in plane shear stress, and the orientation of the element at that stress 3. Find the absolute maximum in plane shear stress 4. Find the normal stresses and shear stress when the element is rotated 30 degrees counterclockwise

Using Mohr's Circle, solve Review problem R9-5 in the 10th Ed. of the text. Plot your solution along with notation of the axes and all the values below on graph paper. Show your calculation for the values below. 1. Find the Principal Stresses, and the orientation of the element at the those stresses 2. Find the maximum in plane shear stress, and the orientation of the element at that stress 3. Find the absolute maximum in plane shear stress 4. Find the normal stresses and shear stress when the element is rotated 30 degrees counterclockwise

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.7P: The normal and shear stresses acting on element A are 6500 psi, 17,300 psi, and 2900 psi (see the...

See similar textbooks

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
The normal and shear stresses acting on element A are 6500 psi, 17,300 psi, and 2900 psi (see the figure b for Problem 7.2-5). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
The stresses acting on a stress element on the arm of a power excavator (see figure) are ax= 52 MPa and txy= 33 MPa (sec figure). What is the allowable range of values for the stress if the maximum shear stress is limited to = 37 MPa?
-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
An element in plane stress from the fuselage of an airplane is subjected to compressive stresses of magnitude 35 MPa in the horizontal direction and tensile stresses of magnitude 6.5 MPa in the vertical direct ion. Also, shear stresses of magnitude 12.5 MPa act in the directions shown (see the figure for Problem 7.2-8). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
Consider the general case of plane stress as shown. Write a computer program that will show a plot of the three Mohr’s circles for the element, and will also determine the maximum in-plane shear stress and the absolute maximumshear stress.
A member is subjected to a major stress of 110 MPa (tensile), minor stress of 40 MPa (tensile) along with a counter clockwise shear stress of 30 MPa. Calculate the Normal stress, tangential stress, Resultant stress and its inclination on plane make 20 to major stress. Validate your analytical results by drawing Mohr’s circle. i) Normal Stress (unit is MPa) = (ii) Tangential Stress (unit is MPa) = ) Resultant Stress (unit is MPa) Resultant inclination (unit in degree) =
For the plane-stress condition given below: σx = 400 MPa σy = 500 MPa τxy = - 30 MPa Construct a Mohr’s circle of stress, find: (a) the principal stresses and the orientation of the principal axes relative to the x,y axes (b) determine the stresses on an element, rotated in the x-y plane 60° counter?clockwise from its original position ; Show these stresses on a sketch of an element oriented at this angle (c) Also, using the matrix transformation law to compare the solutions with Mohr’s circle
Draw and stress tensonr with the following characteristics The stress cube visualization at point A would depict the normal stress (σ_x) acting on two opposite faces and the shear stress (τ_xy) acting tangentially on the four sides associated with torsion.