So, rise in temperature= 64.11-LUAdditional QuestionsV- 2,5 V239.5) per) In a test to determine the resistance a cable, anappliedwas necessary to produce a current od (2A) at cis C).joltagea. Calculate the cable resistance at (55°C) if the temperot-oefticient at CO°C) is (1/235) per °C.b. If the cable Carries (10 A) at this temperature, calculatethe power dissipated in the cable.[145, 145W]

The correct solution can be achieved as follows.

V- 2.5 V re L) In a test to determine the resistance A a cable, an applied was necessary to produce a current of (2A) at cis c). Joltage a. Calculate the cable resistance at (55°C) if the temperat coefticient at C0°C) is (1/235) per °C. b. If the cable Carries (10 A) at this teaperature, calculate the power dissipated in the cable. C14S, 145 W]

V- 2.5 V re L) In a test to determine the resistance A a cable, an applied was necessary to produce a current of (2A) at cis c). Joltage a. Calculate the cable resistance at (55°C) if the temperat coefticient at C0°C) is (1/235) per °C. b. If the cable Carries (10 A) at this teaperature, calculate the power dissipated in the cable. C14S, 145 W]

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.1P: The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C...

See similar textbooks

Similar questions

A three phase, 33 KV, underground cable system, consider a single core of conductor radius 0.8 cm diameter and lead sheath of 2.3 cm. The core and lead sheath have been separated by two intersheaths with radius 1.3 cm and 1.8 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same. Please i need it know please
A three phase, 11 KV, underground cable system, consider a single core of conductor radius 0.5 cm diameter and lead sheath of 1.25 cm. The core and lead sheath have been separated by two intersheaths with radius 0.75 cm and 1 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same.
5. A 2-wire DC ring distributor is 375m long and is fed with 300V at point A. At point B, 200m from A, load of 150A is taken and at point C, 100m in the opposite direction, a load of 100A is taken. If the resistance per 100m of single conductor is 0.03, find: i. Current in each section of distributor ii. Voltage at points B and C iii. Point of minimum potential
On the 1km long dc distributor above the applied voltage at point O is 200V. Lengths ??? = 100?,??? = 600? and the impedance for the conductor material per 10000m is ?? = 5 < 53.130Ω. Calculate:a. The potential at point C b. Current along section OC of the distributor
An overhead line has span of 260m. The tension in the line is 1200kg while the conductor weighs 650 kg per 100 meters. Calculate the maximum SAG in the conductor. If the height of the tower is 13 meters, estimate the clearance of conductor to the ground. Draw a figure and mark values of sag, clearance, span, height of conductor etc.
Theoretically solve an unknown resistance for Transmission line conductor by using any two methods (for example: Wheatstone bridge, Kelvin bridge, Potentiometer method etc). And then compare them and state that between in this two used methods which one is better and why. [Note: You can choose any practical value for ratio arms]
Subject: Electrical & Electronics Engineering Course: Power Systems Question: What is GMR and GMD? Explain your answer in case of a composite conductor.
For the polished conductors having radius of 1 cm equally at a distance of 100 cm, caring of 3 phase supply line under 76 cm pressure at 25 degree centigrade. For the standard condition, find the minimum phase neutral voltage at which corona occurs.
The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft (or 0.05112 ohm per km) at 20 degree celcius and a 60 Hz resistance of 0.0956 ohm per mile (or 0.0594 ohm per km) at 50 degree celcius for the all-aluminum Marogold conductor, which has 61 strands and whose size is 564 mm2 or 1113 kcmil. Assuming an increase in resistance at 50 degree celcius, and determine the percentage due to skin effect.
One thousand circular mils or 1 kcmil is sometimes designated by the abbreviation MCM75C. Data for commercial bare-aluminum electrical conductors lists a 60 Hz resistance of 0.0080 ohm per kilometer at for a 793-MCM AAC conductor. Determine the cross-sectional conducting area of this conductor in square meters. Find the 60 Hz resistance of this conductor in ohms per kilometer at 50C.
On your own understanding, what is solid wire conductor and stranded wire conductor and where are they used in building electrical systems?
Besides the number of turns and the legth of active conductor, whit of the following is?are a factor which affects the amount of emf(voltage) induced in a coil? A) how fast the conductor is moving through the field(rate of incidence), B) the strength of the magtnetic field(flux density), C) the angle at which the conductor is cutting the magnetic field( angle of incidence), D) all of the above What is mean by genarator regulation? A) it is the percentage rise in terminal voltage from no-load to full-load, B) it is the percentage rise in terminal voltage full-load to no-load, C) it is the amount of control one has over the terminal voltage by way of the field excitation, D) none How are transformer components indetified? The algebraic symboly for the number of kilovolt-amperes on the load side of the transformer is_____. A) KVAh, B) KVAx, C) KVA-primary, D) KVA-secondary