Give explanation and use the calculations in the second image. Was your average experimental mass percent of oxygen in potassium chlorate higher or lower than thetheoretical value (circle one)?HigherLowerWhich of the following sources of error could be used to explain this discrepancy (circle one)?A. The potassium chlorate sample was not heated strongly or long enough.B. Some of the potassium chloride product splattered out of the crucible during the heating process.Explain your choice. Your response should include an analysis of the calculations you performed withraw data to obtain your experimental % of oxygen.your Mass of original KClO3 sample=Mass of KCl residue =Mass of Oxygen released =Mass Percent of Oxygen in KC103Average Mass Percent Oxygen =-KCIO3] -Sample 1[Mass of crucible, lid +[Mass of crucible + lid] =33.745 g - 32.721 g = 1.024 g[Mass of crucible, lid + residueafter 2nd heating] -[Mass of crucible + lid] =33.314 g - 32.721 g = 0.593 gMass of original KCIO3 sample -Mass of KCI residue =1.024 g - 0.593 g = 0.431 g42.090 +39.4442Mass Percent of Oxygen (experim-Mass Percent of Oxygen (experim-ental) = Mass of Oxygen released /ental) = Mass of Oxygen releasedMass of Potassium chlorate used x Mass of Potassium chlorate used x100 = 0.431 g / 1.024 g x 100 = 100 = 0.383 g / 0.971 g x 100 =42.090 %39.444%81.534Sample 2[Mass of crucible, lid + KCIO3] -[Mass of crucible + lid] =33.692 g - 32.721 g = 0.971 g2[Mass of crucible, lid + residueafter 2nd heating] -[Mass of crucible + lid] =33.309 g - 32.721 g = 0.588 gMass of original KCIO3 sample -Mass of KCI residue=0.971 g - 0.588 g = 0.383 g= 40.767 %

One mol KClO3 contain 3 mol of oxygen and 1 mol of K and 1 mol of Cl Molecular mass of KClO3 = 122.5…

Was your average experimental mass percent of oxygen in potassium chlorate higher or lower than the theoretical value (circle one)? Higher Lower Which of the following sources of error could be used to explain this discrepancy (circle one)? A. The potassium chlorate sample was not heated strongly or long enough. B. Some of the potassium chloride product splattered out of the crucible during the heating process. Explain your choice. Your response should include an analysis of the calculations you performed with your caw data to obtain your experimental % of oxygen.

Was your average experimental mass percent of oxygen in potassium chlorate higher or lower than the theoretical value (circle one)? Higher Lower Which of the following sources of error could be used to explain this discrepancy (circle one)? A. The potassium chlorate sample was not heated strongly or long enough. B. Some of the potassium chloride product splattered out of the crucible during the heating process. Explain your choice. Your response should include an analysis of the calculations you performed with your caw data to obtain your experimental % of oxygen.

Organic Chemistry: A Guided Inquiry

2nd Edition

ISBN:9780618974122

Author:Andrei Straumanis

Publisher:Andrei Straumanis

ChapterL3: Carbon (13c) Nmr Spectroscopy

Section: Chapter Questions

Problem 13CTQ

See similar textbooks

Similar questions

What is a reagent blank? Why should we include this in making our calibration curve?
What is/are the limiting reagent(s) for this three-step procedure? Why is sodium borohydride not the limiting reagent even though a smaller number of moles of this reagent are used? Mass/volume used in experiment: O-vanillin = 0.760g P-toluidine = 0.535g Ethanol = 15 ml Sodium borohydride = 0.1 g Glacial acetic acid = 2 ml Acetic anhydride = 2 ml
with a theoretical yield of 80% compute for the percent error of the following data Vial weight= 18.3501 vial + fluorescein weight=18.442 resorcinol = 0.1502g Phthalic anhydride= 0.1022g
Each of the student statements below is wrong. Explain why they are not correct. (a) All my compound dissolved right away in the small amount of solvent I added at room temperature, and I didn’t need to heat it at all. This means I’m going to get lots of pure compound out. (b) I did a recrystallization of naphthalene and my percent recovery was very high (99%), so I must have pure product. (c) When you’ve dissolved all your compound in hot solvent, and you’re in a hurry, it’s ok to just place it straight into the ice bath.
Give an observation and inference hexane is subjected into lucas test and Metallic sodium test
Recall that the formula for ΔHrxn = [(-Ccal)(moles of limiting reactant)/(ΔT)]If the actual concentration of the sodium hydroxide used in the calibration part of the experiment was lower than the stated value, will the value of Ccal increase, decrease, or remain the same? Please explain. How about if the actual concentration of the sodium hydroxide used in the calibration part of the experiment was lower than the stated value. However, the NaOH solution used in the determination of ΔHrxn was of the correct concentration. Will the magnitue of ΔHrxn increase, decrease, or remain the same? Please explain.
6 PLEASE PROVIDE THE INTERPRETATION OF ALL SAMPLES FOR HELPFUL RATINGS. THANK YOU. *INCLUDE ALL YOUR REFERENCES
Would the change in your overall end product change any data points you were given?
Please help me calculate the theoretical yield of [Ru(phen)3)][PF6]2 as seen in the procedure below!
In the crude product, explain why you might obtain a yield which appears to be greater than 100%.
Now that you know the moles of NaOH used for each trial as well as the volume of NaOH used for each trial, calculate the concentration of the NaOH that you made in lab for each trial. Round to the ten-thousandths place please.
Mass spectrometry. Circle the answer below. Please show solution (structures and m/z).