Don't give handwritten solution. Water (density 1000 kg/m) flows through an inclined pipe of uniform diameter. Thevelocity. pressure and elevation at section A are V, = 3.2 m/s, P, =186 kPa andZ, = 24.5 m respectively, and those at section B are Ve = 3.2 m/s, Pa = 260 kPa andZ, = 9.1 m, respectively. If acceleration due to gravity is 10 m/s then the head lostdue to friction ism (round off to one decimal place).

Answered: Image /qna-images/answer/9089600e-a1ba-4264-97bc-416a1629361d.jpg

Water (density 1000 kg/m) flows through an inclined pipe of uniform diameter. The velocity. pressure and elevation at section A are V, = 3.2 m/s, P, =186 kPa and 2 = 24.5 m respectively, and those at section B are Ve = 3.2 m/s. Pa = 260 kPa and z, = 9.1 m, respectively. If acceleration due to gravity is 10 m/s then the head lost m (round off to one decimal place). due to friction is

Water (density 1000 kg/m) flows through an inclined pipe of uniform diameter. The velocity. pressure and elevation at section A are V, = 3.2 m/s, P, =186 kPa and 2 = 24.5 m respectively, and those at section B are Ve = 3.2 m/s. Pa = 260 kPa and z, = 9.1 m, respectively. If acceleration due to gravity is 10 m/s then the head lost m (round off to one decimal place). due to friction is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pipe A, 30 cm in diameter, branches into two pipes B and C. Pipe B is 15 cm in diameter and pipe C is 7.5 cm in diameter. If the flow in A is divided as follows 2/3 goes to B and 1/3 goes into C, what is the discahrge in pipe A, if the velocity must not exceed 3 m/s in any of the pipes?
In fluid flow equations, the variable p/ϒ is called A. Pressure Head B. Velocity HeadC. Static Head D. Total Head
Minor losses through valves, fittings, bends, contractions etc. are commonly modeled as proportional to (a) total head (b) static head (c) velocity head (d) pressure drop (e) velocity
Water (density 1000 kg/m?) flows through an inclined pipe of unform diametar. The velocity. pressura and elevation at section A are V, = 3.2 mis, p, =186 kPa and 2, = 245 m respectively, and those at section B ara V = 3.2 /s, py = 260 kPa and 2y = 9.1 m, respectivoly. If accaleration due 1o gravity /s 10 m/s* then the head lost due to friction is ‘m (round off 1o one decimal place).
pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
A 60-cm water pipe carries a flow of 0.1 m³/s. At point A the elevation is 50 meters and the pressure is 200 kPa. At point B, 1200 meters downstream from A, the elevation is 40 meters and the pressure is 230 kPa. The head loss , in feet, between A and B isA. 6.94B. 15.0C. 20.88D. 100.2
PROBLEM 5: In Lake Geneva (Switzerland), there is a water jet (called the Jet d’Eau) that is discharged 130 m straight upward (measured from the surface of the lake). The exit of the discharge pipe is 20 cm in diameter.
A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.
A fan draws air at rest and propels it 45 meters through a rectangular duct measuring 200 by 300 mm. At a rate of 0.6m3/s, air enters at 15°C and 750 mm Hg absolute pressure. What is the required theoretical power?
A certain axial flow turbine has an output torque M that isproportional to the volume flow rate Q and also depends onthe density ρ , rotor diameter D , and rotation rate Ω . Howdoes the torque change due to a doubling of ( a ) D and ( b ) Ω ?
Water from a reservoir passes over a dam through a turbine and discharges from a 70-cm ID pipe at a point 95 m below the reservoir surface. The turbine delivers 0.950 MW. Calculate the required flow of water in m3/min if friction is neglected. If friction were included would a higher or lower flow rate be required? (Note: The equation you will solve in this problem has multiple roots. Find a solution less than 1.0 m3/s.) V=___m^3/min?
In Fig. there are 125 ft of 2-in pipe, 75 ft of 6-inpipe, and 150 ft of 3-in pipe, all cast iron. There are three90° elbows and an open globe valve, all flanged. If the exitelevation is zero, what horsepower is extracted by the turbinewhen the flow rate is 0.16 ft3/s of water at 20°C?