3).in the figure below. Consider the acceleration due to gravity as g=32.2 ft/s², specific weight ofwater as yw-Pwg=62.4 lb/ft³ and gasoline as ygasoline=Pgasolineg=42.5 lb/ft³.What pressure, pi, is needed to produce a flowrate of 0.09 ft³/s from the tank shownAirGasoline2.0 ftSalt water3.6 ftSG = 1.10.06-ft diameter -

Answered: Image /qna-images/answer/76942607-a360-4375-8951-78c9da6baa13.jpg

What pressure, pi, is needed to produce a flowrate of 0.09 ft/s from the tank shown 3). in the figure below. Consider the acceleration due to gravity as g=32.2 ft/s², specific weight of water as yw-pwg-62.4 lb/ft and gasoline as ygasoline=FPgasolineg=42.5 lb/ft°. P1 Air Gasoline 2.0 ft Salt water SG = 1.1 3.6 ft 0.06-ft diameter-

What pressure, pi, is needed to produce a flowrate of 0.09 ft/s from the tank shown 3). in the figure below. Consider the acceleration due to gravity as g=32.2 ft/s², specific weight of water as yw-pwg-62.4 lb/ft and gasoline as ygasoline=FPgasolineg=42.5 lb/ft°. P1 Air Gasoline 2.0 ft Salt water SG = 1.1 3.6 ft 0.06-ft diameter-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given: Two(2) identical pumps series in connection Suction Pressure = 3.2 Bars Discharge Pressure = 4.95 Bars Suction Pipe Dia = 450mm Discharge pipe Dia = 480mm Velocity of Water = 4.25 m/s Solve: Total Head, Pump1 & 2 individual head and if Pump 2 is 9.5% less than Pump 1 and Or = Total Flow Rate
Pumps: A centrifugal pump having 4 stages in parallel, delivers 18 kiloliters/min of liquid against a head of 25 m. The diameter of the impellers being 24 cm and the speed of 1800 rpm. A pump is to be made up with a number of stages in series of similar construction to that of the first pump to run at 1250 rpm and to deliver 15 kiloliters/min against a totalhead of 250 m. Find the diameter of the impellers and the number of stages required in this case. Answer: D = 46.63 cm, n = 6 stages
Q Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
1) A single-stage centrifugal pump operating at 650 rpm and delivering 250 gallons per second has a specific speed of 4750 rpm. The suction flange is 609.6 mm in diameter and has a vacuum pressure of 70 kPa. The discharge flange is 22 inches in diameter and its centerline is 30.5 cm above the suction centerline. What discharge pressure in kPaa would you expect to find?
The large reservoir in the following figure provides water for the indicated tank with a flow rate of 10 L/s. Check that the machine is installed and a pump or a turbine, and determine its power, if the yield is 75%. Suppose ideal fluid. Data: γH20 = 104N/m3 ; ATubes = 10mc2 ; g = 10m/s2 .
Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
4. A centrifugal pump has r2 = 9 in., b2 = 2 in., and 2 = 35 and rotates at 1060 rev/min. If it generates a head of 180 ft, determine the theoretical (a) flow rate, in gpm; and (b) horsepower. Assume near-radial entry flow. a. flow rate Answer : _______________ gpmb. water horsepower Answer : _______________ HP
PAY ATTENTION TO THE QUESTION : What is the resulting flow rate in the system if three pumps are used in parallel? (a) 0.483 m^3/s (b) 0.364 m^3/s (c) 0.333 m^3/s (d) 0.563 m^3/s 1. The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . IT SAYS : if theee pumps are used in parallel PAY ATTENTION Multiple choice choose correct answer
Two pumps (Pump A and B) have performance curves which can be approximated by the following equations: H_A = 340 - (1.2(Q^2)), in feet H_B = 360 - (2.5(Q^2)), in feet where Q is in ft^3/s. If pumps A and B were to operate in parallel as depicted in the figure below, at what head (in ft.) should either pump be operated?
Suppose that you are willing to determine the diameter of the water jet impinging to the sink from the kitchen tap.The tap is produced to supply three different flow rates of the low, medium, and high. For each flow rate level, waterthat comes from the tap fills the beaker with a volume of 30 mL in 10 s, 6 s, and 2 s, respectively. The outlet of the tapis 13 mm, and the distance between the tap outlet and the sink is 53 mm. Determine the diameters of the water jetimpinging on the sink at three given flow rates.
A turbine rotates at 150 rpm and discharges 0.8 m3/s. The radial velocity at inlet Cr1 = 2 m/s and equals 6 m/s at exit. The physical data are: r1 = 0.5 m, r2 = 0.2 m, α1 = 15°, β2 = 135°, Z1 = Z2, the pressure head at exit is 6 m. Assuming a loss of head of 2 m, calculate the following: The water horsepower delivered by the turbine, (no draft tube are used) neglect circulatory flow and hydraulic losses. The pressure head, in meters, at the entrance. The degree of reaction.
Chlorine gas enters a 30-mm ID pipe at 15 m/s, and exits a wider pipe, at 85-mm ID. What is the average velocity through the exit pipe (in m/s)?