Answered: Water flowing through a 4.5-cm-diameter…

Water flowing through a 4.5-cm-diameter pipe can fill a 200 L bathtub in 2.0 min. What is the speed of the water in the pipe in m/s?

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter9: Mass And Mass-related Variables In Engineering

Section: Chapter Questions

Problem 46P

See similar textbooks

Related questions

Q: * .R.L. is same as B.M False O True O we can measure the horizontal distance between the Level instr...

A: We have to determine the given statement in the question is either false or true as per the knowledg...

Q: d the resulting error in closure.

Q: The following T-Beam has given properties: Effective Depth (d) = 485 mm, thickness of the slab = 100...

Q: V (kN) | 10 - 2nd-degree curve -x (m) -2 -8 -1¬-1¬–2-

A: We are given SFD Area of it will give force And bending moment slope will given by shear force it s...

Q: A canal 6 m deep runs through a soil having C = 18 kN/m², o = 10°, e = 0.8 and G = 2.72. The angle o...

A: Given data,

Q: What is the minimum pressure difference between A and B which would allow an upward flow through thi...

A: CALCULATE of minimum Pressure difference between A and B####

Q: Compute the deformation of the beam using area method: E= 200 GPa I= 1000 x 106 mm4

A: Given Data E = 200 GPa I = 1000x106 mm4

Q: A sample of 1346 grams of soil was taken from a 792 cu.cm test hole. It was then oven-dried and weig...

Q: 66KN |2 ft| -4 ft→- 6 ft 6 ft 6 ft D E A B 15 ft |C 24 ft-

Q: A cylinder vessel filled with Wa and spilled half of its volume. Estimate the angular velocity in re...

Q: A 150-lb wrecking ball B is attached to a 40-ft-long steel cable AB and swings in the vertical arc s...

Q: Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have t...

Q: A 150-wrecking ball B is attached to a 40-ft-long steel cable AB and swings in the vertical arc show...

A: To determine the tension in the cable when the wrecking ball is at position D. Given, Weight of ...

Q: Show complete solution and 3 decimal places for the final answer. Asap thanks! A cube container wi...

Q: Discuss the different types of stresses.

Q: Q1.(50%): A partially submerged body is towed in water. The resistance force R to its motion depends...

A: step 1-

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforc...

A: To Find - b) What is the value of fs' (actual stress of the compression bars)

Q: Sulfur hexafluoride (psF. = 6.17 kg/m³) and nitrogen (pPN2 = 1.292 kg/m³) are fed into a mixing tank...

Q: Consider a cylinder of specific gravity SG < 1 floating vertically in water (SG = 1), as in the figu...

Q: 1. Determine the maximum weight P that can be held in the position shown just before the machine beg...

A: To find out the, 1) Maximum weight P that can held in position before the machine begin to tip. 2)...

Q: A soil is made up of identical spherical aggregates of bulk density Pz= 1.3 g/cm3 whose solid phase ...

A: In this question we have to determine the value of bulk density of the soil, the aggregate porosity,...

Q: 47 КРа 4Z KPa 28 KPa 2Y kPa D A 8X КРа 81 КРа 706 F B E For the state of stress as shown in Figure. ...

Q: A tubular post of outer diameter d, is guyed by two cables fitted with turnbuckles (see figure). The...

A: Tensile strength of cable = 110 kN Allowable compressive stress of post = 35 MPa

Q: The stiffness matrix for the given coordinates of the beam as shown in the figure is

Q: 3. Calculate the % composition in terms of mass of a solution obtained by mixing 300g of a 25% & 400...

A: Given-concentration= 300 g of 25% and 400 g of 40%

Q: A tie-down on the deck of a sailboat consists of a bent bar bolted at both ends, as shown in the fig...

Q: The table summarizes the distribution of students in college. Use Slovin’s Formula to determine a pr...

Q: 78k/ft А 6 ft – -18 ft

A: Compute the internal loadings acting at a section passing through point C.

Q: stresses in each element. E=30E6 psi, Elemer ment 3 has Area = 20 in?, Use both software an 6 ft 2

Q: The discharge of water in a 25 cm diameter pipe is 0.05 m3/s. What is the mean velocity?

Q: Three equal parallel resistors are to a 10 volts dc source. If the total current of the circuit is 2...

Q: In an ore-mixing operation, a bucket full of ore is suspended from a travelling crane which moves al...

Q: Determine the required tension steel area for the following conditions: A) MDL = 150 kN.m, MLL = 120...

A: Flange width(bf) = 820 m Flange thickness(tf)= 100 mm Width of web(bw)= 250 mm Effective depth(d)= 4...

Q: 30 kN/ - 6 m

A: Given : Cantilever beam with UVL Conjugate Beam Method

Q: Rod Reading 1.23 Rod Reading B.46 Horizontal Line of Skght 1.23 B 8.46 Turning Point 755.11 Mean Sea...

Q: alculate the forces in members CG,GF and CF for the truss show 2 kN 2 m B 2m C 2m

Q: A cylinder vessel filled with water with a 2m diameter and 5m high. It was rotated with uniform angu...

Q: Two reservoirs, A and B, are connected together by the two pipes with a pump between them. Assuming ...

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforc...

Q: In a demonstration of the momentum of fluid flow, a circular plate was suspended in equilibrium on t...

Q: Problem 2. A cantilever beam 3m long has its ends resting on rigid supports and carries a concentrat...

Q: Consider a simple rectangular beam (bxh) reinforced with steel reinforcement of A.. Assume b = 8 in....

Q: The height of water in the reservoir at the U/S of an earth dam is 12 m and the maximum length of th...

A: We are provided with height of water And also length, angle of friction between dam and soil beneat...

Q: In an ore-mixing operation, a bucket full of ore is suspended from a travelling crane which moves al...

Q: Problem #2: Determine the forces acting in members FE, EB and BC of the truss use the method of sect...

Q: The coefficients of friction between the load and the flat-bed trailer shown are 0.35 (static) and 0...

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforc...

A: Beam can be characterized as an underlying part which conveys every upward burden and opposes it fro...

Q: 2. Attach a complete solution. Draw the cash flow diagram. Suppose that P 4500 is deposited each yea...

Q: Q1: Find the diameter of indentation for steel with the • :following information ** Brinell hardness...

Q: 1O KN A 6 m 6 m

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

100%

Water flowing through a 4.5-cm-diameter pipe can
fill a 200 L bathtub in 2.0 min. What is the speed of
the water in the pipe in m/s?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A plastic cup, 15.0 cm in height, is filled to the rim with water and is resting on a table. A small hole is punctured in the cup at a height 9.00 cm above the bottom of the cup and is allowing water to spew out. What is the speed of the water when it strikes the table?
Water is flowing in a 60mm pipe at rate of 15 m3 per hour. what is the maximum velocity of a flow?
Water is pumped into a storage tank from a well delivering 20.0 gallons of water in 30.0 seconds through a pipe of 1.in2 cross-sectional area. What is the average velocity of the water in the pipe as the water is pumped from the well?
Calculate the diameter of a pipe that must carry 140 L/min at a velocity of 5 m/s *.
A rectangular duct with dimensions of 30 cm×35 cm delivers conditioned air to a room at a rate of 30 m3⁄min . What should be the size of a circular duct if the average air velocity inside the duct is to remain the same?
Water flows through a pipe 25 mm in diameter at a velocity of 6 m/s. Determine whether the flow will be laminar or turbulent assuming that the dynamic viscosity of water is taken as1.30 × 10−3 kg/ms and its mass density as 1000 kg/m3. If oil of specific gravity 0.9 and dynamic viscosity 9.6 × 10−2 kg/ms is pumped through the same pipe, what type of flow will occur?
Imagine the water level in the tank described rises at a rate of 4 mm/s. Knowing the diameter of the tank is 240 mm, what is the average velocity of the water leaving the tank?
A pipe 12 inches in diameter has water flowing through it at 3 m per second. What is the discharge incubic meter per second (cms)? In liter per minute (lpm)?
A rectangular duct with dimensions of 1 m × 110 cm delivers conditioned air with a density of 1.2 kg⁄m3 to a room at a rate of 45 m3 /min. What is the mass-flow rate of air? What is the average air speed in the duct?
What is the theoretical velocity of a jet of water flowing out of a square orifice in a large tank if the center of the orifice is 600 mm below the water surface?
The discharge of water in a 25 cm diameter pipe is 0.05 m3/s. What is the mean velocity?
A tank is in the shape of an inverted cone, having height h = 2.5 m and base radius r = 0.75 m. If water is poured into the tank at a rate of 15 L/s, how long will it take to fill the tank? Water flows into a cubical tank at a rate of 15 L/s. If the top surface of the water in the tank is rising by 1.5 cm every second, what is the length of each side of the tank?