Water flowing through a pipe at a rate of 70 liter/sec having diameters 600 mm and 400 mm at the bottom and upper end respectively. The intensity of pressure at the bottom end is 4 bar and the pressure at upper end is 1.2 bar. Determine the distance of upper end of the pipe from datum line if the lower end is 120 cm above the datum line.

Water flowing through a pipe at a rate of 70 liter/sec having diameters 600 mm and 400 mm at the bottom and upper end respectively. The intensity of pressure at the bottom end is 4 bar and the pressure at upper end is 1.2 bar. Determine the distance of upper end of the pipe from datum line if the lower end is 120 cm above the datum line.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.34P: 2.34 Show that the temperature distribution in a sphere of radius . made of a homogeneous material...

See similar textbooks

Similar questions

A Liquid fluid with a density of 1,750 kg/m3 from an elevated 2m open reservoir (P1=0 bars) flows before the pump at 7.5 m/s. The liquid fluid is pumped at an unknown final velocity to a 75 meter elevated tank with a pressure reading of 7.75 Bars. assuming Friction losses is 757.75J and the actual WORK of the pump is 1,933,400J. Calculate the power in HP if the pump's efficiency is just 75% and for every 1,000 kg of fluid per hour.
A Liquid fluid with a density of 1,750 kg/m3 from an elevated 2m open reservoir (P1=0 bars) flows before the pump at 7.5 m/s. The liquid fluid is pumped at an unknown final velocity to a 75 meter elevated tank with a pressure reading of 7.75 Bars. assuming Friction losses is 757.75J and the actual WORK of the pump is 1,933,400J. Calculate the Final Velocity in m/s if the pump's efficiency is just 75% and for every 1,000 kg of fluid per hour.
A water pump delivers 6 hp of shaft power when operating. If the pressure differential between the outlet and the inlet of the pump is measured to be 1.2 psi when the flow rate is 15 ft^3/s the changes in velocity and elevation are negligible, determine the mechanical efficiency of this pump. Show the energy diagram and label it accordingly
Two chambers, Chamber 1 and Chamber 2 where pressure at chamber 1 p1=70 kPa, at chamber 2 the pressure p2 = 5kPa. There is an orifice between the two chambers with diameter of 6 cm, Cc= 1.00, Cv=0.95 and the head of the liquid(s=2.50) over the orifice is 1.80 m. Find the actual flow rate through the orifice.include your free body diagram.a.35 L/s b.25 L/s c.15 L/s d.45 L/s
water circulates throughout a house in a hot water heating system. if the water is pumped at a speed of 0.55 m/s through a 6.0-cm diameter pipe in the basement under a pressure of 3.03x105 pa, what will be the velocity and pressure in a 2.6-cm diameter pipe on the second floor 5.0 m above?
A cylindrical pipe with a cross-sectional radius r = 1.40[cm] is plunged into a l = 2.30[m] tall open water drum that is initially completely filled with water (pwater = 1000 [kg/m3]). The pipe goes h1 = 0.35 [m] above the drum before dropping down h2 = 3.50 [m] below the base of the drum as shown. The cross-sectional radius of the top side of the pipe is R = 2.20 [cm].A. How fast is the water going out of this pipe?B. What's the liquid's pressure at the top of the pipe? Assume that the system is exposed to 1.00 [atm] of air pressure.C. What's the maximum height the pipe can go above the drum before the water stops flowing out of the pipe? For liquid flow to be continuous, the liquid’s pressure must not fall before its vapor pressure. Assume that vapor pressure, in this case, is 2.30 [kPa].
Water enters a hydraulic turbine through a 30-cm-diameter pipe at a rate of 0.7 m3/s and exits through a 25-cm-diameter pipe. The pressure drop in the turbine is measured by a mercury manometer to be 1.2 m. For a combined turbine–generator efficiency of 83 percent, determine the net electric power output. Disregard the effect of the kinetic energy correction factors. Take the density of water to be 1000 kg/m3 and the density of mercury to be 13,560 kg/m3.
The pump of a water distribution system is powered by a 15-kW electric motor whose efficiency is 90 percent. The water flow rate through the pump is 50 L/s. The diameters of the inlet and outlet pipes are the same, and the elevation difference across the pump is negligible. If the pressures at the inlet and outlet of the pump are measured to be 100 kPa and 300 kPa (absolute), respectively, determine the mechanical efficiency of the pump.
The brake horsepower and water horsepower of a pump are determined to be 15 kW and 12 kW, respectively. If the flow rate of water to the pump under these conditions is 0.05 m3/s, the total head loss of the pump is (a) 11.5 m (b) 9.3 m (c) 7.7 m (d) 6.1 m (e) 4.9 m
Q2// Water enters a hydraulic turbine through a 26 cm diameter pipe at a rate of 1.2 m^3/s and exits through a 21 cm diameter pipe. The pressure drop in the turbine is measured by a mercury manometer to be 2 m. For a combined turbine generator efficiency of 91%. determine the net electric power output. Disregard the effect of the kinetic energy correction factors.
A liquid of specific gravity of 1.75 flows in a 6 cm horizontal pipe. The total energy at certain point in the flow is 80 J/N (joules/newton). The elevation of the pipe above the fixed datum is 2.6 m. If the pressure is 75 kPa. Determine the power available at the specified point in kW. include your free body diagram A.148.91 B.142.25 C.144.22 D.146.96
Two chambers, Chamber 1 and Chamber 2 where pressure at chamber 1 p1=70 kPa, at chamber 2 the pressure p2 = 5kPa. There is an orifice between the two chambers with diameter of 6 cm, Cc= 1.00, Cv=0.95 and the head of the liquid(s=2.50) over the orifice is 1.80 m. Find the actual flow rate through the orifice. Include the free body diagram if needed. a.45 L/s b.15 L/s c.35 L/s d.25 L/s