Please solve it with explanation.thx. (D Sayfa görünümüA Sesli okuE VurgulaZID AWater flows from a nozzle with a speed of V =10m/sStream diameter 0.1 m%3DNozzleand is collected in a container that moves toward the-MovingcontrolvolumeV = 10 m/snozzle with a speed of Vcv = 2 m/s as shown in theV = 2 m/sfigure. If the water between the nozzle and the tank is3 min the constant diameter stream, what is the accumu-lation rate of water in the tank?

Velocity of stream wrt. ground = V = +10 Velocity of container wrt. ground = Vcv = -2 ( opposite…

Water flows from a nozzle with a speed of V = 10m/s %3D and is collected in a container that moves toward the nozzle with a speed of Vcv = 2 m/s as shown in the figure. If the water between the nozzle and the tank is in the constant diameter stream, what is the accumu- lation rate of water in the tank?

Water flows from a nozzle with a speed of V = 10m/s %3D and is collected in a container that moves toward the nozzle with a speed of Vcv = 2 m/s as shown in the figure. If the water between the nozzle and the tank is in the constant diameter stream, what is the accumu- lation rate of water in the tank?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 75 L/s, and leaves the sprinkler nozzles as 2-cm diameter jets at an angle of ? from the tangential direction, as shown. The length of each sprinkler arm is 0.52 m.For the specified flow rate, investigate the effect of discharge angle ? on the rate of rotation n. by varying ? from 0° to 90° in increments of 10°. Plot the rate of rotation versus ?, and discuss your results.
SAE 10 oil at 20 °C flows through the 4-cm-diameter verticalpipe of Fig. P6.30. For the mercury, manometer readingh = 42 cm shown, (a) calculate the volume flow rate inm3/h and (b) state the direction of flow.
pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
The reservoirs in Fig. are connected by cast iron pipesjoined abruptly, with sharp-edged entrance and exit. Includingminor losses, estimate the flow of water at 20 °C if the surfaceof reservoir 1 is 45 ft higher than that of reservoir 2.
estimate the allowable distance Y if the allowable pressure in the systems is -18kPa (gage). aasume that the volume flow rate is 5.6 x 10^-3 m^3/s
A horizontal pipe of diameter 350 mm converges to a diameter of 200 mm. The pipeconveys water with a density of 1 g/cm3. The pressure at the inlet and outlet are 550kPa and270 kPa respectively. Assuming the flow is incompressible and frictionless, estimate themass flow rate through the pipeline, stating the velocity at both the inlet and outlet.
An 11.5-in-diameter centrifugal pump, running at1750 r/min, delivers 850 gal/min and a head of 105 ftat best efficiency (82 percent). (a) Can this pump operateefficiently when delivering water at 20°C through200 m of 10- cm-diameter smooth pipe? Neglect minorlosses. (b) If your answer to (a) is negative, can thespeed n be changed to operate efficiently? (c) If youranswer to (b) is also negative, can the impeller diameterbe changed to operate efficiently and still run at1750 rev/min?
SAE 10 oil at 20°C flows through the 4-cm-diameter vertical pipe of Fig. P6.30. For the mercury manometer reading h = 42 cm shown, (a) calculate the volume flow rate in m3/h and (b) state the direction of flow.
Homework Question: SAE 10W oil at 20oC flows from a tank into a 2.5 cm-diameter tube 50 cm long. The flow rate is 1.15 m3/hr. Is the entrance length region a significant part of this tube flow? HINT : The flow rate is 1.15 m3/hr. & flows from a tank into a 2.5 cm-diameter tube 50 cm long***
Oil, with a vapor pressure of 20 kPa, is delivered througha pipeline by equally spaced pumps, each of which increases the oilpressure by 1.3 MPa. Friction losses in thepipe are 150 Pa per meter of pipe. What is the maximumpossible pump spacing to avoid cavitation of the oil?
In a turbulent flow in a 0.3 m pipe the centerline velocity is 6 m/s, and that 50 mm fromthe pipe wall 5.2 m/s. Calculate the friction factor and flowrate.
Suppose that there is a 4-cm water jet with a velocity of 15 m/s which hits a vertical plate with a mass on 800 kg. This plate is mounted on a track which is nearly frictionless and starts out not moving. when the jet strikes the plate, water leaves by splashing out in the plane of the plate. what is the acceleration of the plate when the jet first hits it? What is the velocity of the plate after 60 seconds? Assume that the momentum correction factor s 1.04.