Q.2.A. Blood flows through the branching blood vessels as shown in figure at a rate of 1o Aaln ft/s. If viscous effects are negligible, determine the water speed at section (2), the 10 ts pressure at section (3), and the flow rate at section (4). Polood 1000 kg/m (1) A 0.22 (3) V 20t/s P- 10 psi (2) Ag= 0.07 t? 5.0 psi

Q.2.A. Blood flows through the branching blood vessels as shown in figure at a rate of 1o Aaln ft/s. If viscous effects are negligible, determine the water speed at section (2), the 10 ts pressure at section (3), and the flow rate at section (4). Polood 1000 kg/m (1) A 0.22 (3) V 20t/s P- 10 psi (2) Ag= 0.07 t? 5.0 psi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. What is the volumetric flow rate between two plates if the top plate is pulled, while keeping the bottom plate stationary, and simultaneously imposing pressure p0 on the left endof the channel, and pressure p0 + ∆p (∆p > 0) on the right end of thechannel.
A diverging tube discharges water from reservoir at a depth of 10m below the water surface. The diameter of the tube graduallyincreases from 150 mm at the throat to 225 mm at the outlet.Neglecting friction, determine the maximum possible rate ofdischarge through this tube.
Neglecting head losses, determinewhat horsepower the pump must deliver toproduce the flow as shown. Here theelevations at points A, B, C, and D are 110 ft.200 ft, 110 ft and 90 ft, respectively. The nozzle area is 0.10 ft2
What are the flow Q and the velocity V when total head loss is H = 25 m?
Calculate the total head of the system below. Assume a flow of 70 m³/h and that the pressure drops in the suction and discharge are 3 m and 4 m, respectively. ZA = 15m, ZB = 5m and ZC = 5m.
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450 mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively. If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
Water at 20°C is withdrawn from a reservoir by means of a siphon, as shown in the figure. For d=10cm and D= 16cm, Determine: a) the minimum flow rate that can be achieved without cavitation occurring in the piping system, and b) the maximum elevation of the highest point in the piping system to prevent cavitation. c) Also, comment on the ways to increase the maximum elevation of the highest point in the piping system to prevent cavitation. (The saturation pressure of water at 20°C is 2.33 kPa)
A pump is required to pump water from a large reservoir to the water tower located 20 m above thereservoir (Figure 1). If 0.03 m3/s of water having a density of 1000 kg/m3is pumped through a 30-mmpipe.a. How much power is required to be delivered to the water by the pump? Consider the flow lossesin the pipe; do the necessary assumptions. b. Determine the efficiency of the pump
Two pipes are connected in series with a diameter ratio of 2:5. If the flow velocity in the smaller diameter pipe is 12 m/s, determine the head loss due to: a. sudden contraction, b. sudden enlargement.
(a) Prove that the loss of pressure head for the viscous flow through a circular pipe is givenby h. (b) Determine (i) the pressure gradient, (ii) the shear stress at the two horizontal parallelplates, and (iii) the discharge per meter width for the laminar flow of oil with a maximumvelocity of 1.5 m/s between two horizontal parallel fixed plates which are 80 mm apart. Takeviscosity of oil as 1.962 Ns/m2.
Water flows through a new cast iron (e = 0.26 mm) pipe at a velocity of 4.2 m/s. The length and diameter of pipe are 400 m and 150 mm, respectively. Determine the head loss due to friction if ν = 1.02 x 10-6m/s.