What diameter pipe would be required to deliver a hydraulic fluid with a Sg of 0.86, 100 ft. through drawn steel tubing if the velocity is limited to 10 ft.sec, the friction factor is 0.05 and the pressure drop to 25 Ibf'in? .086 in. 1.38 in. 2.96 in. O4.47 in

What diameter pipe would be required to deliver a hydraulic fluid with a Sg of 0.86, 100 ft. through drawn steel tubing if the velocity is limited to 10 ft.sec, the friction factor is 0.05 and the pressure drop to 25 Ibf'in? .086 in. 1.38 in. 2.96 in. O4.47 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: If given that the hydraulic radius is 1.3 mm and that the roughness,ε is 0.000015 m calculate the…

Q: A pipe with internal diameter, length, coefficient of friction, of 50 mm, 6 m, 0.008, respectively,…

A: Given: Tank D=3m Water level=5m di=50mm=0.05m L=6m ZA=5m ZB= -2m he=0.008

Q: What is the ratio of the average velocity to maximum velocity for water flowing in a 1" schedule 40…

Q: For the parallel-pipe system of D=3 in L= 250 ft Fig. each pipe is cast iron, and the pressure drop…

Q: A 4-inch schedule 80 commercial steel pipe carries water at room temperature through a pipe network…

A: Given:d=4 inQ=10 L/sL=150 m

Q: What is the velocity as measured by an orifice plate (0.06-m diameter) in a 0.305-m-diameter pipe…

A: Given that , d1=0.305md2= 0.06m∆P=75150Pa =75.150kPa

Q: What is the energy loss over a gradual contraction from a DN125 Schedule 40 steel pipe to a DN50…

A: Given data Gradual contraction is from section 1 with DN125 schedule 40 pipe to section 2with DN50…

Q: Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following…

Q: 5. 10 lt / s of water is requested to be transported from A depot to city B. The water level of the…

A: Given: Q=10 L/sL=1000 mf=0.02d=90 mm =0.09 mPressure head at Point B=20 m

Q: 0.027

A: given ε = 1.5 mm) diameter = 0.5 m Reynolds Number = 200 000

Q: 4- Is the flow rate effect the head loss and why? 5- What is the relation between the head loss and…

A: When fluid flows inside a pipeline or a duct , friction occurs between the layers of moving fluid…

Q: A storage tank has hot water. This water at a temperature of 85 °C is pumped to a 600 cm height at a…

Q: Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following…

A: Solution to part (d) as mentioned by the student:

Q: mpute the volumetric flow rate (GPM) of ethanol at 77°F that would occur given the above nditions.…

A: In the question, there are losses in the pipe due to - 1. Pipe firction 2. Pipe bending 3. Half…

Q: 20 oC water must be pumped from A to B which has both atmospheric pressure and B is 6 meters above…

A: Given:Water temperature, T=20°CElevation difference between A and B, zB-zA=6mPipe length,…

Q: A large tank is partly filled with water, the air space above being under pressure. A 2′′ hose…

Q: Determine the Pressure drop in Mpa through a flow control valve that has a capacity coefficient 5…

A: For a flow control valve the flow rate (Q) is given by - Q=C∆PSpecific Gravitywhere C is capacity…

Q: Heavy fuel oil is pumped at a flow rate of 88 L/s through a new steel pipe. What diameter of the…

A: given data- length of the pipe L = 300 m flow rate Q = 88 L/s = 0.088 m3/s friction factor f =…

Q: Water (specific gravity, G, is 1.0 and the kinematic viscosity, ν, is 1.14 *10-6 m2 /s) flows…

Q: A fluid is flowing in a round pipe. The Reynolds number is Re = 3 x 10°. The relative roughness is =…

Q: Question 1 Calculate the frictional head loss of a cast iron pipe, L=100m, v=2m/s, D=2", E= 0.15,…

Q: Problem: : Determine the size of clean wrought-iron pipe required to convey 4000 gpm oil, v = 0.0001…

Q: Conditions the flow rate through the orifice meten is to lo0 /min. of Seawater with P-P = 16 IkPa.…

Q: Water at 75°C 3.83 x10-7m²&9.56 kN) (v= is Sm3. flowing in a standard hydraulic copper tube, 13.4mm…

Q: A 25% Calcium Chloride brine is to be pumped through a line at 250 gpm at a temp. of 0 deg. If the…

A: Given that, Flow rate of chloride, Q=250 gpm,Pressure drop inside pipe, ∆P=0.006 lb·force/in2-ft…

Q: Discuss the flow through the Coarse and soft pip.

A: Coarse Pipe- In coarse pipe, the surface irregularities are more which destroyed the laminar…

Q: water is being delivered at a rate of 2000 gpm for a reservoir to a subdivison below resvoir…

A: RESERVOIR A repository is most generally an augmented regular or fake lake made utilizing a dam to…

Q: If the shear stress at the wall of a 12′′ diameter pipe is 1.00 psf and f = 0.040, what is the…

Q: What diameter is required in a pipe with t=0.2 mm and a length of 2450 m, yes it is desired that…

A: To find : The required diameter in a pipe. Given : The thickness is t=0.2 mm. The discharge is…

Q: A duplex, single-acting reciprocating power pump is driven by a 40-HP electric motor at a speed of…

Q: Water at 100°F is flowing through a straight 4-in schedule 40 pipe at a rate of 1 gal/min. The…

A: The data given is, Discharge, Q = 1 gal/min Length of pipe, L = 10 ft Water temperature, T = 100°F…

Q: What level h must be maintained in Fig. to deliver afl ow rate of 0.015 ft3/s through the 1/2-in…

A: Given data: For Water at temperature 20 degrees Celcius Flow rate = 0.015 ft3/s…

Q: Two pipes 1 and 2 having the following properties are connected in series: Pipe 1 - Length = 1500m,…

Q: 9. What pressure drop in Ibf/in.? could be expected across a 1.5-in. I.D. orifice with a C4 = 0.70…

A: Given: The inner diameter of pipe, d = 1.5 in The coefficient of discharge, Cd = 0.7 The specific…

Q: ir at 27°C flows at 3m pipe and supplies con

Q: Air at a pressure of 120 psig and a temp of 50 deg F is flowing at a rate of 500 lbs/ hr through a…

Q: the following with (True) or (False): 1- The head loss in box culverts varied linearly with the…

A: Given: Statements are given and we have to find which of them are true and which are false. 1- The…

Q: Series pipe ABCD consists of 10,000 ft of 20′′, 8000 ft of 16′′, and L ft of 12′′ (C = 120). What…

A: Given: The length of pipe AB, L1 = 10,000 ft The diameter of pipe AB, D1 =20 in = 1.666 ft The…

Q: 4. Find total loss in the problem Where: Q = 10 litre / second, 1= 0.33 and k for both bends and…

Q: c) A pumping plant forces water through a 600 mm diameter main, the friction head being 27 m. In…

Q: Determine the Pressure drop in Mpa through a flow control valve that has a capacity coefficient 5…

A: Given: Flow coefficient C=5lpm/kpa1/2Flow rate (Q)=0.0015m3/secSpecific gravity (S.G)=0.85

Q: (Sheet No.2) */ waer is tAvans por ted at a5f (10 lor Goolt in (1.)in - diameter wroughtiron…

Q: n efficiency óf 72%. Thé surface of e friction pressure drop in the pipe

Q: 10.8 Example Determine the pressure or head losses for a 25 mm threaded steel pipe tee flowing 25%…

Q: F00 mm, rough luid in the pipe btained from t what is the % er

A: d=600mme=0.6mmL=2500mQ=450L/sρ=1.25kg/m3v=1.5×10-5m2/s To-Find:- %error

Q: Discuss the relation between the head pressure and flow rate for the benefits of connecting the…

A: When the two pumps are connected in series, their resultant pump performance curve is given by…

Q: Table 6.2 shows the typical volume flow rate for centrif- ugal fire-fighting pumps is in the range…

A: Given: Q=1800 L/min to 9500 L/min V= 2 m/s To find: Diameter

Q: Water 80F at 10 ft/s through a 6 inches sch 40 steel pipe with lenght of 1000ft The Reynolds number…

Q: If the volume flow rate and friction factor is kept the same in a laminar flow pipe but the pipe…

A: The diameter relation is

Q: Estimate the entrance length for motor oil for the following two cases

Question

What diameter pipe would be required to deliver a hydraulic fluid with a Sg of 0.86, 100 ft. through drawn
steel tubing if the velocity is limited to 10 ft.sec, the friction factor is 0.05 and the pressure drop to 25 Ibf'in?
.086 in.
1.38 in.
2.96 in.
O4.47 in

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 25% Calcium Chloride brine is to be pumped through a line at 250 gpm at a temp. of 0 deg. If the allowable pressure drop is 0.006 lb force per s. in-ft pipe, what size of pipe is required
The water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height difference between exit and entry planes is stated as 50 ft. The yield of waterpump, 80% the power of pump motor is 20 horsepowers. Friction losses are stated as 50ft-lbf/lbm. Please calculate the flow rate in pipe line.
water is being delivered at a rate of 2000 gpm for a reservoir to a subdivison below resvoir height=220ft length of pipe= 1500ft final aubdivisiion= 24ft, 20psi 1)determine the normal pipe size 2) if the pipe size is not avalible what size combination will work 3) if we used a 8 inch pipe determine the min thickness 4)determine the max pressure that can deelope in the 8in system
Estimate the entrance length for motor oil for the following two cases: (a) SAE10W-30 oil flowing through a 0.1-in diameter tube in an engine at 0.01 gal/s and (b) SAE 10W-30 oil flowing through a 6-in diameter pipe at 500 gal/s.
Calculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40 steel pipe if the vol-ume flow rate is 0.25 ft3 / s: (a) water at 60F, (b) acetone at 77F, (c) castor oil at 77F, and (d) SAE 10 oil at 210F (sg = 0.87).
Determine the smallest metric hydraulic copper tube size that will carry 4L/min of thefollowing fluids while maintaining laminar flow: (a) water at 40°C, (b) gasoline(SG=0.68) 25°C, (c) ethyl alcohol (SG=0.79) at 0°C, and (d) heavy fuel oil at 25°C. answer correctly the last part only please thank you
Calculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40 steel pipe if the vol- ume flow rate is 0.25 ft/s: (a) water at 60°F. (b) acetone at 77 F, (c) castor oil at 77 E, and (d) SAE 10 oil at 210°(Sg 0.87),
Water at 100°F is flowing through a straight 4-in schedule 40 pipe at a rate of 1 gal/min. The length of the pipe is 10 ft, find the velocity at the center of the pipe in feet per second?A. 0.0378B. 0.0504C. 0.0454D. 0.0252
What level h must be maintained in Fig. to deliver afl ow rate of 0.015 ft3/s through the 1/2-in commercial steel pipe?
The flow rate of a hydraulic fluid with a Sg of 1.08 through a 2-in. I.D. orifice is 50 gal/min. If the pressure drop across the orifice is 5 lbf/in.", what is the discharge coefficient?
In an annular section made of commercial steel pipe with an outer diameter or 13.78 inches inside a commercial steel pipe with an inner diameter of 23.62 inches carries a water flowrate of 600L/sec. The total length of the section is 10m. What is the frictional loss in meters of water at a temperature of 68o F?
What is the ratio of the average velocity to maximum velocity for water flowing in a 1" schedule 40 pipe? Assume laminar flow.A. 0.8B. 0.9C. 0.6D. 0.5