When the voltage source is turned off in a simple circuit consists of a resistor and an inductor, the rate of decrease of the current is proportional to the current. The current is 40 amperes at the moment that the switch is off and dies down to 15 amperes after 0.01 sec. Determine the current in 0.02 sec. 3.375 amperes 4.25 amperes 5.625 amperes 6.025 amperes

When the voltage source is turned off in a simple circuit consists of a resistor and an inductor, the rate of decrease of the current is proportional to the current. The current is 40 amperes at the moment that the switch is off and dies down to 15 amperes after 0.01 sec. Determine the current in 0.02 sec. 3.375 amperes 4.25 amperes 5.625 amperes 6.025 amperes

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter32: Inductance

Section: Chapter Questions

Problem 32.16P

See similar textbooks

Similar questions

A 60.0-ft resistor is connected in series with a 30.0-F capacitor and a source whose maximum voltage is 120 V, operating at 60.0 Hz. Find (a) the capacitive reactance of the circuit, (b) the impedance of the circuit, and (c) the maximum current in the circuit. (d) Does the voltage lead or lag the current? (e) How will adding an inductor in series with the existing resistor and capacitor affect the current? Explain.
A 2.0-F capacitor is charged to a potential difference of 12.0 V and then connected across a 0.40-mH inductor. What is the current in the circuit when the potential difference across the capacitor is 6.0 V?
Can a circuit e1eent have both capacitance and inductance?
A 1.5k resistor and 30-mH inductor are connected in series, as below, across a120-V(rms)ac power source oscillating at 60-Hz frequency. (a) Find the current in the circuit. (b) Find the voltage drops across the resistor and inductor. (C) Find the impedance of the circuit. (d) Find the power dissipated in the resistor. (e) Find the power dissipated in the inductor. (1) Find the power produced by the source.
You are working in a factory and have been tasked with determining the electrical needs for a new motor that will be installed on an assembly line. The motor has been tested under load conditions and found to have a resistance of 35. and an inductive reactance of 50.0 . We can model the motor as a series RL circuit. The motor will have its own dedicated circuit with an rms voltage of 480 V. You need to determine the peak current drawn by the motor to determine the size of the circuit breaker needed to protect the circuit.
If the capacitors in Figure 23.55 are replaced by inductors, which acts as a low-frequency fitter and which as a high-frequency fitter?
Construct Your Own Problem Consider the use of an inductor in series with a computer operating on 60 Hz electricity. Construct a problem in which you calculate the relative reduction in voltage of incoming high frequency noise compared to 60 Hz voltage. Among the things to consider are the acceptable series reactance of the inductor for 60 Hz power and the likely frequencies of noise coming through the power lines.
In Figure 14.12, =12V , L = 20 mH, and R=5.0. Determine (a) the time constant of the circuit, (b) the initial current through the resistor, (C) the final current through the resistor, (d) the current through the resistor when t=2L , and (e) the voltages across the inductor and the resistor when t=2L .
Your RL circuit has a characteristic time constant of 20.0 ns, and a resistance of 5.00 M (a) What is the inductance of the circuit? (b) What resistance would give you a 1.00 ns time constant, perhaps needed for quick response in an oscilloscope?
What capacitance should be used to produce a 2.00 M(reactance at 60.0 Hz?