Which of the following apply to a mating set of spur gears: Select one: O a. Thrust is significant O b. Noise will be louder than an equivalent helical gear set. O c. Large reductions, typically > 20:1, are possible. O d. None of these options

Which of the following apply to a mating set of spur gears: Select one: O a. Thrust is significant O b. Noise will be louder than an equivalent helical gear set. O c. Large reductions, typically > 20:1, are possible. O d. None of these options

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter38: Manual Transmissions And Transaxles

Section: Chapter Questions

Problem 5ASRQ: Technician A says that if a single idler gear is used to obtain reverse gear, its size and number of...

See similar textbooks

Related questions

Q: Examine the gear drive system shown below. All the gears have a DP = 12. The smallest gear is the…

Q: 1- What is the benefit of the epicyclic gear train? Name s ome applications?

A: Epicyclic gear train :

Q: Identify the number of spur gears available in a Single Purchase Crab Winch a. One b. Three c. Four…

Q: RI NG GEAR Stage 2 PLANETARY GEAAS ARM Stage 1 OUTPUT SHAFT CTOOL SPINOLE) CATTACHED TO ARMO…

Q: A transmission system with a pair of beveled gears has the following data: 25° gear angle, 20° full…

A: Bevel gears are the gears meshed together in order to achieve maximum efficiency through minimal…

Q: 6. Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and…

A: Given that, Two spur gear of 40 teeth and 120 teeth Pinion rotates at 1200 rpm Torque is 20 N.m

Q: bevel ring gear Q.1 State the purpose of the differential. derential gear (sde gear) diferential…

A: Solution: To Find: (a) Purpose of the differential. (b) (c)

Q: A gear box conta8he 3 sizes of gears, 8 tooth, 32 tooth and 64 teeth. What is the gear ratio when…

A: Given data: The number of tooth on input gear, T1 = 8. The number of tooth on output gear, T2 = 64.…

Q: Increasing the pressure angle of two mating spur gears results in.. Select one: O a. reduced…

A: Gear is defined as a mechanical component utilised to convey the power of one shaft to another…

Q: Technician A says that a Simpson gearset is two planetary gearsets that share a common sun gear.…

A: Given data : Simpson gear set Ravigneaix gear set

Q: Choose the correct answer: - In a set of meshing gears, forces are transmitted on ….. which is…

A: To choose the correct option.

Q: Sentences tic strength of the gear tooth is based on....... strength bending b. compressive c. shear…

A: Ans: 1. b. Compressive 2. a. Surface 3. b. Max 4. b .two 5. c. Helix angles 6. c. Less than…

Q: Evaluate the conditions needed for an epicyclic gear train to become a differential, and show how a…

A: Gears are used to transmit motion from one shaft to another or between a shaft and a slide. An…

Q: (b) Determine the safe power which can be transmitted by a pair of helical gears, 20° full depth,…

A: Gears are the two rings having teeth on it which are meshed together to transmit the power. They are…

Q: n epicyclic gear train, as shown in Fig.

Q: Identify different types of teeth which are across a gear - one is known as a spur or 'straight cut'…

A: Solution: To Find: (a) Identify the types of Teeth on the respective gears. (b) Need of respective…

Q: What are the harmful effects of backlash error in gears?

A: Backlash is basically the clearance or gap or space between the mashing teeth. And backlash error is…

Q: As for an external standard spur involute gear, if its deddendum circle and its base circle…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: Q1:- A pair of spur gears with 12 and 20 teeth are made with an involute form, pressure angle 20°…

Q: picyclic gear in Fig. 11. er of teeth on 0 and 200. De

Q: #2: For the two-gear system shown in following figure; a) Calculate Gear Ratio b) If the…

A: Given: Teeth on the driven gear is 50. Teeth on the driver gear is 114. Speed of the driver gear is…

Q: From the following options, choose the condition(s) that is(are) required for the proper meshing of…

A: Two helical gears for meshing should have the following parameters, Same Pitch. Same Pressure…

Q: Questions and discussions 1- Explain two industrial applications of the spiroid gears. 2- Find gear…

Q: Describe gear and classification of gears and detail also explain terms used in gears?

Q: What is the final output RPM of the 64-tooth gear? What is the final output Torque supplied by the…

Q: Compare the differences between different gear profiles

A: There are two types of gear profiles are present (i) Cycloidal profile (ii) Involute profile

Q: Calculate the final drive gear ratio for a differential using a ring gear with 49 teeth and a…

A: Gear: The rotational machine element that helps in the transmission of power between two or more…

Q: Which type of gear develop gear whine at high rotational speed? a.Spur gear b.Helical gear c.Both a…

A: Gear whine is a noise that occurs due to the vibration caused during the time of transmission at a…

Q: State two advantages of a compound gear train over a simple gear train

A: Given: One gear train is simple gear train and other gear train is compound gear train. Determine:…

Q: What are proper meshin involute snur gears?

A: given:

Q: explain the use of compound gear instead of a simple gear train ( no more than 50 words)

A: Q.6 SOLUTION With the use of Compound gear train we can create much change power and velocity of…

Q: Explain the working of epicyclic gears with a neat diagram

A: Given Data : Epicyclic gears

Q: The following particulars of a sıngle reduction spur gear are given. gear ratio = 10 to 1, distance…

A: Given data: Gear ratio, G=101=TGTP, where TG=Number of teeth on driven gear wheel and TP=Number of…

Q: Which one of the following is the correct statement ? The consequence of a slight increase in the…

A: Basics of Gears.

Q: You have engaged in open discussion in which you have to evaluate the conditions needed for an…

A: The work of differential is to provide different power to the different output shafts. This…

Q: 5(a) Why mechanical actuation is important in mechatronics system? Classify various types of gears.…

A: Component of a Machine that is responsible for moving and controlling a mechanism or system is…

Q: which type ot gears have point contact between two mating gears? olect the coect answer * Helical…

A: These questions are based on the concept of gears.

Q: 1- What is the benefit of he epicyclic gear train? lame some applications? 2- Why does efficiency…

A: To find :- 1.Benefit of epicyclic gear train 2.a) Why efficiency increases with increase in load b)…

Q: Clearly explain the directions for forces on mating spur gears mounted on two parallel shafts. Draw…

A: Introduction Spur gears are a type of cylindrical gears with straight teeth and are mounted on the…

Q: A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The module…

Q: Q#2: For the two-gear system shown in following figure; a) Calculate Gear Ratio b) If the…

A: Let, teeth on the driver gear are 300.Assume T1 & T2 are the teeth on the driver and driven…

Q: A gear rotating at 1250 rpm is meshed is being driven by another gear at 500 rpm. If the driver…

Q: ndum in helic

A: given: what is the equation of the addendum and dedendum in helical gears

Q: cycloidal g

A: The cycloidal gear profile, as opposed to the involute gear profile used in most other gears, is a…

Q: its of cycloid g

A: The cycloidal gear profile, as opposed to the involute gear profile used in most other gears, is a…

Q: Q2+ State adantages of Gyeloidal Involute profile gear tooth pufile. as a

A: Advantages of the cycloidal gear tooth profile: There are some advantages of cycloidal gear tooth…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Which of the following apply to a mating set of spur gears:
Select one:
O a. Thrust is significant
O b. Noise will be louder than an equivalent helical gear set.
Oc. Large reductions, typically > 20:1, are possible.
O d. None of these options
s page

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q#2: For the two-gear system shown in following figure; a) Calculate Gear Ratio b) If the speed of Driver Gear is 30 revolutions per minute (rpm) then what will be speed of Driven Gear? c) Among two gears (driven gear and driver gear), which gear has highest speed in revolutions per minute.? d) What should be number of teeth on Driven gear to move with speed of 4 times than that of Driver Gear? (Hint: If your ID is 114-2020, then compression force would be 114 N)
Compare the differences between different gear profiles
Examine the gear drive system shown below. All the gears have a DP = 12. The smallest gear is the primary driver gear and has 15 Teeth, RPM = 3600, and Torque = 2.2 N-m. That small gear meshes with a 72-tooth gear which is connected to another gear that has 20 teeth. That 20-tooth gear connects to the final driven gear that has 64 teeth. What is the TOTAL Gear Ratio for this system? What is the TOTAL Speed Ratio for this system? What is the Center to Center spacing of the first gear set? What is the Center to Center spacing of the second gear set? What is the final output RPM of the 64-tooth gear? What is the final output Torque supplied by the 64 tooth gear?
Q#2: For the two-gear system shown in following figure; a) Calculate Gear Ratio b) If the speed of Driver Gear is 30 revolutions per minute (rpm) then what will be speed of Driven Gear? c) Among two gears (driven gear and driver gear), which gear has highest speed in revolutions per minute.? d) What should be number of teeth on Driven gear to move with speed of 4 times than that of Driver Gear?
Discuss the difference between simple gear train and compound gear train ..
Two mating external 8-pitch, 20o , spur gears have 24 and 64 teeth. Determine the contact ratio.
As shown in Figure 10-26, Please design a gear pair in the reducer of this belt conveyor. The input power is P=60 kW, the rotary speed of pinion is n1=960 r/min, the ration of teeth number is u= 2.5, the reducer is driven by electric motor. the design life is expected 10 years. the belt conveyor runs 12 hours per day. the load is stable.
A transmission system with a pair of beveled gears has the following data: 25° gear angle, 20° full depth involute system pressure angle, 5 in standard diametral pitch, both minion and gear are made of SAE 1040 steel and have a surface width of 3 in. If the number of pinion teeth is 20 and rotates at a speed of 2026 rpm so that the speed ratio becomes 1:5, then calculate how much HP power the system can safely transmit by a pair of inclined gears. To determine the maximum HP power that can be transmitted: (a) Using the modified Lewis and Buckingham equations, and(b) The AGMA method is based on strength only and uses the gear table to determine the required factors
Tech A says that if a noise is caused by a set of worn gears, it will normally be loudest in that gear while driving under a load. Tech B says that if the bearings on the input shaft, countershaft, or main shaft are worn, either front or rear, a growling noise will result when stopped in gear. Who is correct?
Need answer as well as soon Only typed answer needed Handwritten answer not allow There is a helical gear with a right angle module 3mm, a pressure angle of 20°, an inner width of 75 mm, a torsion angle of 25°, the number of pinion teeth 32, rotation angular speed 620rpm, and the number of teeth of the gear 75. If the material of the pinion and gear is SM25C (H b=150], what is the maximum transmission power?[Answer; 4.36 kw]
Explain the working of epicyclic gears with a neat diagram.
Two identical involute, spur gears are in mesh. The module is 4 mm and each gear has 22 teeth If the operating pressure angle is 20° The minimum value of addendum needed to ensure continuous transmission of motion is