Discuss the control system (the level controller and the temperature controllers) shown in figure (2). Specify the controlled and manipulated variable in each case. Discuss the type of the controller used in each case, that is, a simple feedback controller, a feedforward controller, a cascade controller, etc. Draw the block diagram of the temperature control loops. Reactor temperature set point Feed in TT TC D

Discuss the control system (the level controller and the temperature controllers) shown in figure (2). Specify the controlled and manipulated variable in each case. Discuss the type of the controller used in each case, that is, a simple feedback controller, a feedforward controller, a cascade controller, etc. Draw the block diagram of the temperature control loops. Reactor temperature set point Feed in TT TC D

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter16: Advanced Automatic Controls-direct Digital Controls (ddcs) And Pneumatics

Section: Chapter Questions

Problem 3RQ: One advantage of a modern control system is A. simplicity. B. faster response. C. ability to...

See similar textbooks

Similar questions

Example 1.1 Figure 1.5 shows the block diagram of a closed-loop flow control system. Identify the following elements: (a) the sensor, (b) the transducer, (c) the actuator, (d) the transmitter, (e) the controller, (f) the manipulated variable, and (g) the measured variable. In the figure above, the (a) sensor is labeled as the pressure cell. The (b) transducer is labeled as the converter. However, there are two converters: one for converting pressure to current, and another converting current to pressure for operating the actuator. The (c) actuator is labeled as the pneumatic valve. The (d) transmitter is labeled as the line driver. The (e) controller is labeled as the PLC. The (f) manipulated variable is labeled as the pressure developed by the fluid flowing through the orifice plate. The (g) measured variable is the flow rate of the liquid.
1. Give an example of open loop and closed loop system (one example each). Also state the input, control system, feedback and output parameter. Example. 1. Open Loop - Water Heater: Input - Water Temperature (Cold) System - Heating Element Output - Water Temperature (Hot) 2. Closed Loop - Air-conditioning System Input - Desired Room Temperature Control - Motor controller/Compressor/ACU Feedback - Temperature Sensing Output - Room Temperature
(PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare processes develop a control system using feedbackand feedforward concept/principle. Your output is a process and instrumentationdiagram (P & ID) using ISA's Instrument Identification and Symbols standards withexplanation. PROCESS 2: The liquid level inside the tank is regulated at a value of 3.0 m on a condition ofcontinuous liquid inflow and outflow. Requirements: Two feedback solutions One feedforward solution
In the mid-1900s, several technological and analysis concepts came together to make the PID controller widely accepted as an effective industrial controller. Discuss in detail and evaluate the performance of a PID or three-term controllers that are widely used in a typical paper mill where there may be about 2000 control loops, and over 90% of these would be PID control loops.
18- A)Define the following(i) Sensitivity (ii) Transfer function of closed loop control system
a)is the aircraft stable about the equilibrium represented by the transfer function? b) Using proportional feedback,what is the range of acceptable gains for the closed loop systen to be stable? c) Design a feedback control system that allows the pilot to command a pitch angle with overshoot less than or equal to 4.15% and a natural frequency of greater than or equal to 0.99 rad/s d) Design a feedback control system that allows the pilot to command a pitch angle with the same overshoot and a natural frequency of one half the system in part c.
One of the disadvantage of negative feedback loop is lag caused because it can only be exerted after controlled variable has been disturbed. In order to minimize lag between a change in a controlled variable and the action of the effector, it is advantageous for the body to anticipate any likely change. Which one of the following physiological mechanism achieves this? Select one: a. Feedbackward control b. Feedforward control c.Positive feedback control d. All of the above e. None of the above
Design a digital lag compensator for the position control system below to meet thefollowing specifications:ess = 0.0062 in response to a unit ramp reference input, andMp ≤ 0.095 for a unit step reference input.
Develop MATLAB code to model Qacm with a fixed outlet temp of T= 870K. Optimizing components
As far as signals & sytems(s&s) is concerned, discuss using s&s concepts in summary, how a feedback system can be utilized in controlling a water pump in a school.Also make a simple block diagram sketch of the feedback system.
EXPERIMENT TITLE : PID CONTROLLER IN LEVEL CONTROL SYSTEM OBJECTIVE:To demonstrate the characteristic of P,PI and PID controller response on a level controller system. Based on the topic and objective given,please make a clear introduction.
A proportional controller is used to control the height of water in a tank where the water level can vary from 0 to 4.0 m. The required height of water is and the controller is to close a valve fully when the water rises to 3.9 and open it fully when the water falls to 3.1 m. What transfer function will be required? source : Mechatronics: Electronic Control Systems in Mechanical and Electrical Engineering 6th Edition by W. Bolton question 22.4