Which statement is true in the case of the term "Precision". The closeness of output readings when the same input is applied repetitively over a short period of time and there is no change in observer. The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in time of measurement. O The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in location.

Which statement is true in the case of the term "Precision". The closeness of output readings when the same input is applied repetitively over a short period of time and there is no change in observer. The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in time of measurement. O The closeness of output readings when the same input is applied repetitively over a short period of time when there is change in location.

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter54: The Operational Amplifier

Section: Chapter Questions

Problem 7RQ: Name two effects of negative feedback.

See similar textbooks

Similar questions

For the Western Electric rule that if at least 2 of 3 consecutive points fall beyond 2σ to one side of the center line the process is out of control:a. FindtheType1errorrate.b. Find the Type 2 error rate if the process shifts from u to u + 2σ.
18- A)Define the following(i) Sensitivity (ii) Transfer function of closed loop control system
A 12-bit digital-to-analog converter has an output range of 0 to 10 V. Estimate the analog voltage output if the input is simple binary and has the decimal value of 45.
(PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare processes develop a control system using feedbackand feedforward concept/principle. Your output is a process and instrumentationdiagram (P & ID) using ISA's Instrument Identification and Symbols standards withexplanation. PROCESS 2: The liquid level inside the tank is regulated at a value of 3.0 m on a condition ofcontinuous liquid inflow and outflow. Requirements: Two feedback solutions One feedforward solution
Name two effects of negative feedback.
Your factory produces cryogenic refrigerators, and your task is to design a control system for the fridge, but, using the same sensor, you must also supply the end-user with temperature monitoring. The cryogenic freezer is controlled in a tight band around minus 85°C, therefore in controlling the fridge you need to have the most accurate information available regarding the operating range of the fridge (nominally at -85°C, but it can be colder and it can defrost if faulty and reach a maximum ambient temperature of say 50°C to be safe). Due to the economy of RTD sensors, it is decided by management to use a PT100 RTD sensor (range -400°F to 1200°F) with a smart transmitter which needs to be set up correctly to a 4-20mA input on the PLC controlling the fridge. Taking the above conditions into account, the measuring range should be -100°C to 50°C (which should cater for the worst ambient temperature). a) Make sure the RTD is the correct choice b) Set the smart transmitter…
ES EI TD 1) +0.018 -0.015 0.033 2) +0.015 -0.018 0.033 3) +0.018 +0.015 0.003 4) +0.015 -0.015 0.030
1.Design a sequential circuit with two D Flip-Flops, A and B, and one input x. When x = 0, then the state of thecircuit remains the same. When x =1, the circuit goes through the state transitions from 00 to 01 to 11 to 10back to 00, and repeats.
During a start-up of flow loop F-10, a problem is found in which a turbine flowmeter that outputs 4 pulses per gallon (3.79 liters) is now required to have a pulse output of 1 pulse per 500 gallons (1892.71 liters). What is the new scaling factor needed in the totalizer for this change? 4 125 500 2,000
Example 1.1 Figure 1.5 shows the block diagram of a closed-loop flow control system. Identify the following elements: (a) the sensor, (b) the transducer, (c) the actuator, (d) the transmitter, (e) the controller, (f) the manipulated variable, and (g) the measured variable. In the figure above, the (a) sensor is labeled as the pressure cell. The (b) transducer is labeled as the converter. However, there are two converters: one for converting pressure to current, and another converting current to pressure for operating the actuator. The (c) actuator is labeled as the pneumatic valve. The (d) transmitter is labeled as the line driver. The (e) controller is labeled as the PLC. The (f) manipulated variable is labeled as the pressure developed by the fluid flowing through the orifice plate. The (g) measured variable is the flow rate of the liquid.
The response of a system is given by xt=0.003cos 30t +0.004sin 30t m. Determine (a) the amplitude of motion, (b) the period of motion, (c) the frequency in Hz, (d) the frequency in rad/s, (e) the frequency in rpm, (f) the phase angle, and (g) the response in the form of xt=Asin (ωt+φ)
Hello, i am asked to create my own statics problem, these are the specifications. Thank you very much!