While an oil well is being drilled at a depth of 2100 m, it is observed that the top of the 200-mm-diameter steel drill pipe (G= 77.2 GPa) rotates through 2.5 revolutions before the drilling bit starts to operate. Determine the maximum shearing stress caused in the pipe by torsion. The maximum shearing stress caused in the pipe by torsion is MPа.

While an oil well is being drilled at a depth of 2100 m, it is observed that the top of the 200-mm-diameter steel drill pipe (G= 77.2 GPa) rotates through 2.5 revolutions before the drilling bit starts to operate. Determine the maximum shearing stress caused in the pipe by torsion. The maximum shearing stress caused in the pipe by torsion is MPа.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Motor A develops a power of 300 W and drives a pulley at 90 rpm. Determine the required diameters of the steel shafts that drive the pulleys A and B if the allowable shear stress is τ perm = 85 Mpa.
The brass wire has a triangular cross section, 2 mm on a side. If the yield stress for brass is tY = 205 MPa, determine the maximum torque T to which it can be subjected so that the wire will not yield. If this torque is applied to the 4-m-long segment, determine the greatest angle of twist of one end of the wire relative to the other end that will not cause permanent damage to the wire. Gbr = 37 GPa.
Internal loadings at a critical section along a steel drive shaft are given. If the yield stress under tension and shear are S_y = 800 MPa, respectively, determine the maximum length of the shaft using the maximum-shear-stress theory (Tresca yield theory) in a way that the shaft does not fail neither at A nor at B
A rigid plate of negligible mass rests on the middle spring which is higher than the two outer springs by 20 mm. The middle spring consists of 24 turns of 25-mm diameter wire on a mean diameter of 150 mm. The two outer springs have 16 turns of 12-mm diameter wire on a mean diameter of 100 mm. Determine the shearing stress developed in each spring if P = 5 kN is applied. Use the Approximate formula. Use G = 83 GPa. Answer: τm= 95.39 MPa
A torque of 1.4KNm and two forces of 10kN and 12kN are applied to the top of a 65mm diameter solid steel post. Determine the principal stresses and the maximum shear stress at point H and point K.
Would you kindly answer this question. If the shaft must have one uniform diameter, determine the required minimum diameter of the shaft if the normal yield stress in the composite shaft must not exceed 450 MPa with a factor of safety equal to 1.8.
Q3: The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque ofT =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r¡ = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r, = 30 mm 3. Outer tube: r; = 32mm, r, = 38mm
The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 4.0 ft, and c = 8.5 ft, determine(a) the maximum shear stress in the pipe.(b) the rotation angle φC at the free end of the shaft.
The drive shaft of a car with diameter 30 mm is designed to transmit a power of 50 kW when rotating at 2100 rpm. The drive shaft material has an allowable shear stress of 230 MPa. i) Determine the maximum shear stress in the shaft. ii) In order to reduce the weight of the vehicle, a hollow shaft is proposed with a maximum outer diameter of 30 mm. Determine, the maximum inner diameter iii) Determine the resultant percentage weight reduction
A shaft is made of an aluminum alloy having allowable shear stress of tallow = 100 MPa. If the diameter of the shaft is 100 mm, determine the maximum torque T that can be transmitted. What would be the maximum torque T if a 75-mm-diameter hole were bored through the shaft? Sketchthe shear-stress distribution along a radial line in each case.
For a given maximum average shear stress, determine the factor by which the torque-carrying capacity is increased if the half-circular section is reversed from the dashed-line position to the section shown. The tube is 0.1 in. thick.
The drive shaft AB of an automobile is made of a steel having allowable shear stress of tallow = 8 ksi. If the outer diameter of the shaft is 2.5 in. and the engine delivers 200 hp to the shaft when it is turning at 1140 rev>min, determine the minimum required thickness of the shaft’s wall.