shaft is subjected to an axial pull of 22N and transverse sheer force of 12KN The yield strength of the shaft materials is 350Mpa and poison’s ratio 0.3. Determine the diameter of shaft using (i) Maximum Shear stress theory and (ii) Distortion Energy theory (iii) Maximum stress theory (iv) maximum strain energy theory (v) Maximum total strain energy theory.

shaft is subjected to an axial pull of 22N and transverse sheer force of 12KN The yield strength of the shaft materials is 350Mpa and poison’s ratio 0.3. Determine the diameter of shaft using (i) Maximum Shear stress theory and (ii) Distortion Energy theory (iii) Maximum stress theory (iv) maximum strain energy theory (v) Maximum total strain energy theory.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.12P: A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable...

See similar textbooks

Similar questions

The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb # ft, a bending moment of 1500 lb # ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are sY = 100 ksi and tY = 50 ksi, respectively, determine the required diameter ofthe shaft using the maximum shear stress theory.
A steel propeller for a windmill transmits 5.7 kW at 43.4 rpm. If the allowable shear stress in the shaft must be limited to 72 MPa, determine the minimum diameter d required for a solid shaft.
A solid shaft is transmitting 15 MW of power at 1760 rpm. If the allowable shear stress must not amount to 500MPa, determine the size of the shaft.
For design or analysis, is it necessary to know the exact shear-stress distribution on the cross-section? Why?
A shaft is subjected to an axial pull of ___ and transverse shear force of ___ The yield strength of theshaft materials is ___ and poison’s ratio 0.3. Determine the diameter of shaft using (i) Maximum Shearstress theory and (ii) Distortion Energy theory (iii) Maximum stress theory (iv) maximum strain energytheory (v) Maximum total strain energy theory. Also compare the obtained results Givin: Axial pull = 10kN Shear force = 8kN Yield strength= 100MPa Poison’s ratio = 0.3 FOS = 1.0
A shaft is subjected to an axial pull of ___ and transverse shear force of ___ The yield strength of the shaft materials is ___ and poison’s ratio 0.3. Determine the diameter of shaft using (i) Maximum Shear stress theory and (ii) Distortion Energy theory (iii) Maximum stress theory (iv) maximum strain energy theory (v) Maximum total strain energy theory. the Information that you need: Axial pull = 18kN Shear force = 8kN Yield strength = 200MPa
A ship's shaft operates at 150 rpm and resists a maximum shear stress of 50 MPa. The shaft has an outer diameter of 45 cm and an inner diameter of 30 cm, as shown in the figure. Determine: What is the maximum power that can be transmitted without exceeding the allowable shear stress? If the rotational speed of the shaft is limited to half, but the same shaft power is maintained, what happens to the shear stress in the shaft?
A 3-meter solid steel shaft, with an unknown diameter, twists by 5° as it experienced a shear stress of 60 MPa. What is the diameter of the solid steel shaft? Use G = 83 GPa.
A hollow steel shaft with an outside diameter of 64 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 2165 N-m. The shear modulus of the steel is G = 80 GPa. Determine the maximum shear stress in the shaft. 85.3 MPa 72.2 MPa 107.2 MPa 115.4 MPa 92.0 MPa
A generator driven by a wind turbine is required to deliver 5 MW of power at the generator terminals. The turbine is a two-blade propeller rotating about a horizontal axis and the maximum permitted shear stress of the turbine shaft is 55x106 N/m2 The rotor is designed to operate at a rotational speed of 45 revolution per seconds .The stage efficiencies are Cp 0.32, ngb = 0.90, ng = 0.92. %3D . (i) If the turbine delivers its rated power at a wind average speed of 22 m/s, calculate the corresponding diameter of the propeller and its TSR, assuming a typical value for the overall efficiency. The air density may be assumed to have a value 1.29 kg/m³. (ii) Calculate the torque on the turbine shaft.
A solid steel shaft has a diameter of d and a length of L had used to transmit a power of 120 kW at 300 r.p.m. It was recommended that the maximum shear stress and angle of twist are limited to 60 MPa and 1.5 degrees respectively. Determine the diameter and length of the shaft. For the shaft material, G= 80 GPa.
Internal loadings at a critical section along a steel drive shaft are given. If the yield stress under tension and shear are S_y = 800 MPa, respectively, determine the maximum length of the shaft using the maximum-shear-stress theory (Tresca yield theory) in a way that the shaft does not fail neither at A nor at B