You collected the following data from a titration experiment using a 0.123M standardized NaOH solution to titrate a 27.36 mL solution with an unknown Molarity concentration (M) ofsulfuric acid (H2SO4).InitialFinalVolDelivered|(mL)BuretteBuretteReading(mL)Reading(mL)Trial 10.5619.20??Trial 20.5719.7Trial 30.9219.56For just Trial 1, determine the amount of NaOH delivered for the titration with appropriate significant digits. Do not include units.Answer:

Initial burette reading = 0.56 ml Final burette reading = 19.20 ml Volume delivered (ml ) = ?

You collected the following data from a titration experiment using a 0.123M standardized NaOH solution to titrate a 27.36 mL solution with an unknown Molarity concentration (M) of sulfuric acid (H2SO4). Final Vol Burette Initial Burette Delivered Reading (mL) Reading (mL) (mL) Trial 1 0.56 19.20 ?? Trial 2 0.57 19.7 Trial 3 0.92 19.56 For just Trial 1, determine the amount of NaOH delivered for the titration with appropriate significant digits. Do not include units. Answer:

You collected the following data from a titration experiment using a 0.123M standardized NaOH solution to titrate a 27.36 mL solution with an unknown Molarity concentration (M) of sulfuric acid (H2SO4). Final Vol Burette Initial Burette Delivered Reading (mL) Reading (mL) (mL) Trial 1 0.56 19.20 ?? Trial 2 0.57 19.7 Trial 3 0.92 19.56 For just Trial 1, determine the amount of NaOH delivered for the titration with appropriate significant digits. Do not include units. Answer:

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter15: Additional Aqueous Equilibria

Section: Chapter Questions

Problem 34QRT

See similar textbooks

Similar questions

A buffer is prepared by dissolving 0.062 mol of sodium fluoride in 127 mL of 0.0399 M hydrofluoric acid. Assume no volume change after NaF is added. Calculate the pH of this buffer.
Fifty cm3 of 1.000 M nitrous acid is titrated with 0.850 M NaOH. What is the pH of the solution (a) before any NaOH is added? (b) at half-neutralization? (c) at the equivalence point? (d) when 0.10 mL less than the volume of NaOH to reach the equivalence point is added? (e) when 0.10 mL more than the volume of NaOH to reach the equivalence point is added? (f) Use your data to construct a plot similar to that shown in Figure 14.10 (pH versus volume NaOH added).
Sources of Error Determine the relationship between the observed/apparent value (EX) VERSUS that of the true value (ET) for the quantity being sought by writing either <, >, or = on the space provided TOPIC: Standardization of Titrant Question 7 Distilled water was not equilibrated to room temperature before the preparation of NaOH titrant. EX __ ET TOPIC: Determination of Molar Concentration of each component (Double Indicator Titration) Question 8 No blank correction Ex ___ ET Question 9 Bubbles trapped in the tip of burette: EX ___ ET Question 10 Measuring the sample volume using a volumetric pipet while looking downwards at the meniscus: EX ___ ET
What do you call the stage of the titration in which the number of moles of the titrant is stoichiometrically less than the number of moles of the analyte? pre-equivalence equivalence end stage post-equivalenc
For a super special lab titration that I love to do: I would like for the equivalence points to fall at between 20mL and 40mL. Therefore a rough trial will be run using between the window of 0.20-0.25g of the solid and titrating quickly until a sharp pH jump occurs, indicating the second equivalence point. If a rough trial of 0.2190g of unknown acidrequires 41.54mL of NaOH to reach the second equivalence point, what mass of acid should be used to get the second equivalence point to fall at 40.00mL? Thank you!
Calculate the pH during the titration of 40.00 mL of 0.1000 M HCl with 0.1000 M NaOH solution after the following additions of base:(a) 0 mL(b) 25.00 mL(c) 39.00 mL(d) 39.90 mL(e) 40.00 mL(f ) 40.10 mL(g) 50.00 mL Use the values obtained to sketch a curveof [H₃O⁺] vs. mL of added titrant. Are there advantages or dis-advantages to viewing the results in this form? Explain.
explain if this is true or false 1. in the potentiometric titration curve of salicylic acid, the dominating species from the post equivpt are salicylate and hydroxide anions.
An automatic titration of Cola product was analyzed and the following results were produced: Volume of Standardized NaOH Titrant used to achieve the first equivalence point in titration: Trial #1: 1.300 mL Trial #2: 1.137 mL Trial #3: 1.140 mL May you explain why trial #1 was skewed; for example, if pipetting of the 25.00 mL was done incorrectly, how would the molarity change if the volume examined was supposed to be 24.50 mL?
The graph below, which is related to a titration curve, shows the fraction (f) of the stoichiometric amount of acetic acid present as non-ionized CH3COOH and as acetate ion, CH3COO-, as a function of the pH of the solution containing these species. (Graph piture attached) Explain the significance of the point at which the two curves cross. What are the fractions and the pH at that point?
While preparing the samples for analysis, you forgot that you already added phenolphthalein indicator so you added some more. What will be its effect in the volume of the titrant needed to reach the endpoint? Select one: A. Increase B. Decrease C. No effect D. Cannot be determined Primary standards are used to determine the exact concentration of the titrant. Based on the criteria of primary standards, which of the following cannot be used as a primary standard? Select one: A.Oxalic acid B. Sodium hydroxide C. Sodium carbonate D. Potassium dichromate During titration, you notice that the retention of the faint pink color is longer than earlier. Your lab partner suggested that you add a “half-drop” to prevent over-titration of the analyte solution. Is it ethical to do the “half-drop” technique? Select one: A. NO. It will cause error in calculations if you forgot to record the volume reading before adding the half-drop. B. YES. No error in calculations will be encountered provided…
Suppose 100 mL of 2.0 × 10–4 M Fe(NO3)3is added to 100 mL of 2.0 ×10–5 M KIO3. What is Qsp value? Will it precipitate?
please stop rejecting. we pay for this service, so we deserve getting our answer! I do not want to have to put a claim in and report Use acid-base titration to determine theconcentration of:– A strong acid: HCl 0.100 M NaOH (standardized)•0.100 M HCl0.100 M CH3COOH Phenolphthalein is used for endpoint determination– Changes from colourless to pink as a solution becomes more basic• Only need 2-3 drops per titration• pH range: 8.3-10