Drive shaft coupling on a ship propulsion motor PROBLEM 1.9-2

Q: 3.7-5 The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in.,…

A:

Q: A solid, circular bar ABC consists of two segments, as shown in the figure. One segment has a…

A: When a shaft is subjected to torque, shear stress produces in the shaft. The torsion equation is…

Q: For the loaded beam shown in Figure Q6 below, consider section M-M and detemine the following: 6.1…

A: Given Data: Length of the beam, L=0.4+0.3+0.4=1.1 m

Q: A hollow steel shaft used in a constructionauger has an outer diameter d2 = 6.0 in. and…

A: Given d1 = 4.5 in d2 = 6 in G = 11 X 106 psi T = 150 kip-in To find Shear at outer surface Shear at…

Q: 6. The steel shaft of a socket wrench is 12 mm in diameter and 450 mm long (see figure). If the…

A:

Q: A torque T is applied to a thin-walled tubehaving a cross section in the shape of a regular…

A: Given   b = Length of side    t = Thickness Find Shear stress τ  Rate of twist

Q: The steel shaft of a socket wrench has a diameter of 8.0 mm and a lengthof 200 mm (see figure).If…

A: As we know that,  GφL=τd/2φ=2τ0LGd here, G is the shear modulus of the material,  d is the shaft…

Q: A solid tapered steel shaft is rigidly fastened to a fixed support at one end and is subjected to a…

A:

Q: 3.5-2 The outer diameter of the hollow aluminum shaft (see figure) is d 2 =100 mm^ and the inner…

A:

Q: As shown in the figure, a force P-150N and a torsional moment T=400N.m are applied on the free end…

A: Draw the free-body diagram of the shaft.

Q: A section of double-extra-strong pipe made of steel with yield strength Oy = 50ksi is subjected to a…

A: Write the given data with suitable variables. σY=50 ksiM=114.2 kip-inT=254.2 kip-indi=2.3 indo=3.5…

Q: A simply supported beam -b<y<b, 0 <x<L, as shown below, is subjected to a compressive load of half…

A: σy= -3  4bx δ2Mδx2[y33b2-y] +c3f(x)+c4σy=0 at uy=-bc3f(x)+c4=34 δ2Mσx2 x 23=      σy=-3…

Q: A stepped shaft ACB having solid circularcross sections with two different diameters is heldagainst…

A: Consider TA be the resisting torque developed in shaft AC and TB be the resisting torque developed…

Q: A torque T0 is transmitted between two flangedshafts by means of ten 20-mm bolts (see figure…

A: Given   Diameter, d = 250 mm  Shear stress = 85 MPa Find   Maximum torque, T

Q: When drilling a hole in a table leg, a furnituremaker uses a hand-operated drill (see figure) with…

A: The shear stress in the bar, when it is subjected to torsional moment can be calculated using the…

Q: A hollow aluminum shaft (see figure) has an outside diameter d,- 3.4 in. and inside diameter d, -…

A: Data given-  d2 = 3.4 in  so  r = 1.7 in  d1 = 1.7 in  Angle of twist per unit distance = 0.46°/ft…

Q: The composite beam in the figure is made of steel and aluminum. Beam In steel and aluminum as it is…

A: Given: Esteel=210GPa Eal=70GPa M=2kNm Solution: The position of the neutral axix is exactly at the…

Q: A cylindrical pressure vessel with flat ends is subjected to a torque T anda bending moment M (see…

A: Cylinder stress is a stress distribution with rotational symmetry in mechanics, meaning that it does…

Q: applied to the beam in the figure with the notches below and a hole of diameter d in the middle.…

A:

Q: espectively, is fixed on one end and torsional forces (T=10 kN.m) are applied at joining points as…

A: givensolid shaft made of steel aluminium and bronze length of each segments L=3m=3000mmtorsional…

Q: 3.4-18/ A prismatic bar AB of length L and solid circular cross section (diameter d) is loaded by a…

A: GIVEN DATA - A SHAFT WITH DIA d LOADED UNIFORMLY TORQUE WE HAVE TO FIND BOTH POINT a and b

Q: A thin-walled steel tube having an ellipticalcross section with constant thickness t (see figure)…

A: Given Torque, T = 18 k-in.            G = 12 x 106 psi             t = 0.2 in            a = 3.0 in.…

Q: 4 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C,…

A:

Q: 3.44. A circular shaft having diameters D and d and a groove of radius r (see Fig. 3.17, with M=0…

A:

Q: A prismatic bar AB of length L and solidcircular cross section (diameter d) is loaded by…

A: Given   Diameter = d      Length = L Find Maximum shear stress Angle of twist

Q: subjected to pure tor s the inner radius n. strain in the tube is m

A:

Q: 5.5-18 Determine the maximum tensile stress o, and maximum compressive stress o due to the load P…

A:

Q: A section of double-extra-strong pipe made of steel with yield strength Oy = 50ksi is subjected to a…

A: Given data R=78 Ksi= Kilo pound per square inch and kip=1000 pound force  σy=50Ksi=50×103…

Q: A stepped shaft ACB having solid circularcross sections with two different diameters is heldagainst…

A: Consider TA be the resisting torque developed in shaft AC and TB be the resisting torque developed…

Q: A solid, circular bar ABC consists of two segments, as shown in the figure. One segment has a…

A: Given,

Q: In the crank arm of the figure, two loads P act as shown: one parallel to the x axis and another…

A: (a) Draw the given diagram with support reactions, Now, apply force equilibrium in x-direction,…

Q: A stepped shaft ABC consisting of two solid circular segments is subjected to torques '1 and T,…

A:

Q: 3.7-1 A generator shaft in a small hydroelectric plant turns at 120 rpm and delivers 50 hp (see…

A:

Q: F3.A shaft is composed of two 6-in. diameter sections coupled together (see figure below). Part AB…

A: Introduction: A composite shaft is formed when two shafts of different materials are joined together…

Q: (a) If the diameter of the shaft is d = 75 mm, what is the maximum shear stress tmax of the shaft?…

A:

Q: A hollow steel shaft used in a construction auger has outer  diameter d2 = 7.8 in. and inner…

A: Given data:

Q: A round steel rod is subjected to axial tensile stress of 50 MPa with superimposed torsional shear…

A: Given: The value of tensile stress is бx=50 MPa. The value of torsional shear stress is τxy=100…

Q: 7. A stepped shaft ABC consisting of two solid circular segments is subjected to torques Tị and T;…

A: Data given -  d1 = 58 mm = 0.058 m  L1  = 760 mm = 0.76 m d2  = 45 mm = 0.045 m  L2 = 510 mm = 0.510…

Q: 3.7-4 The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 2500…

A:

Q: Question 3 - Torsion ( A composite shaft is shown in the figure below which is fixed against…

A:

Q: 3.7-2 A motor drives a shaft at 12 Hz and delivers 20 kW of power (see figure). (a) If the shaft has…

A: Given dataPower delivered the shaft P = 20kWShaft frequency f = 12Hz1) To determine maximum shear…

Q: T.L J =- (r* – r*) (Tubular shaft) Tr J = (Solid shaft) G.J 3. The shaft in the figure below…

A: Free body diagram: From the FBD: TA+TB=5100 N-m    .....(1)For parallel connection, Angle of…

Q: 3.44. A circular shaft having diameters D and d and a groove of radius r (see Fig. 3.17, with M=0…

A: Given:D=28 mmd=20 mmr=4 mmζall=150 MPa

Q: A stepped shaft ABCD consisting of solid circular segments is subjected to three torques, as shown…

A: The individual angle of twist of the sections needs to be calculated to get the resultant at D. Also…

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate…

A: Given data, σpunching= Average punching shear stress in the collar = 100 MPa σbearing = Average…

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate…

A:

Q: M-2000 Ncm 500 Ncm M-800 Nem M300 Ncm M-400 Ncm A B- L-20cm M.

A:

Q: P-2 kN d- 60 mm Q- IkN | 600 mm Calculate the safe shear stress value of the shaft, given that the…

A:

Q: Q.3) The figure shows a hollow cylindrical shaft of outer diameter do 50 mm and inner diameter d; =…

A:

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.