The linkage of the braking system consists of the pedal arm DAB, the connecting rod BC, and the hydraulic cylinder C. At what angle θ will the force Q be four times greater than the force P applied to the pedal? Neglect friction and the weight of the linkage.

Q: The spring of the mechanism works under tension and at the same moment it exerts a tension force of…

A:

Q: 3. Determine the smallest horizontal force P that would push the homogenous cylinder of weight W…

A: As per given question  We have to find force required to puah the cylinder

Q: The lumbar portion of the human spine supports the entire weight of the upper torso and the force…

A: Make the FBD for the given question.

Q: Determine the force P required to maintain the 240-kg engine in the position for which = 21. The…

A:

Q: The mass center G of the 1400-kg rear-engine car is located as shown in the figure. Determine the…

A:

Q: Determine the force P required to maintain the 235-kg engine in the position for which θ = 40°. The…

A:

Q: 4. The mine car and its contents have a total mass of 6000 kg and a centre of gravity at G. If the…

A:

Q: Determine the force P required to maintain the 150-kg engine in the position for which 0= 21°. The…

A:

Q: homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs. Motion…

A:

Q: 1. Determine the force F to maintain the bell crank shown in equilibrium. Neglect friction at Pivot…

A:

Q: Determine the contact force between the smooth 90-kg ball B and the horizontal bar, and the…

A: Given, m = Mass of the ball = 90 Kg Free body diagram of the ball where, T is the tension in the…

Q: Calculate the magnitude of the clockwise couple M required to turn the 40-kg cylinder in the…

A: Given that, Mass of the cylinder, m=40 kg,Diameter of the cylinder, D=810 mm,Kinematic coefficient…

Q: Determine the magnitude P and direction 0 of the force required to impart a rearward acceleration a…

A:

Q: The uniform rod AB has a mass of (50) kg. Determine the force in the cable when the rod is in the…

A:

Q: A puck weighs 10 lb and rests on the center of the frictionless surface of the ramp supported in…

A:

Q: Determine the force P required to maintain the 200-kg engine in the position for which 0 = 30o. The…

A:

Q: 200 N A block placed under the head , of the claw hammer as shown greatly facilitates the extraction…

A: → Consider the free body diagram of the above figure ,

Q: 2 -Determine the magnitude (P) of the horizontal force required to initiate motion of the block of…

A: Data given - Friction coefficient = 0.5 Weight = mg = 30N

Q: Determine the force P required to maintain the 200-kg engine in the position for which 0 = 30o. The…

A:

Q: The 60-lb homogeneous disk is suspended from a belt that runs from B to C. The spring OA holds the…

A: Free body diagram of disc

Q: 05: The 50-kg homogeneous smooth sphere resèts on the two inclines. Determine the contact forces at…

A:

Q: Determine the force P required to maintain the 195-kg engine in the position for which 0 = 29°. The…

A:

Q: The man is holding up the 35-kg ladder ABC by pushing perpendicular to ladder. If the maximum force…

A: Given:- Mass of the ladder (m) = 35 kg Force (F) = 400 N To Find:-  Angle (θ )

Q: the 75-kg cylinder A is supported by a flexible cable C at 200 and a smooth plane. Determine all…

A:

Q: The 85-lb force P is applied to the 200-lb crate, which is stationary before the force is applied.…

A:

Q: The 700-N force is applied to the 100-kg block, which is stationary before the force is applied.…

A: Let us draw the free body diagram

Q: While slowly walking, a man having a total mass M places all his weight on one foot. Assuming that…

A:

Q: The man pushes the 60-kg homogeneous crate with the horizontal force P. Determine the largest…

A:

Q: Four balls of equal radii form a pyramid supported by a smooth horizontal plane surface. The three…

A: Given: There are four balls of equal radius. So let the radius of each ball is r From the symmetry…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: Consider the diagram shown below for the given system.

Q: 2 -Determine the magnitude ( P ) of the horizontal force required to initiate motion of the block of…

A: In the given problem, we will assume the surface on which the block with mass m is sliding with zero…

Q: 4.95 The linkage of the braking system consists of the pedal arm DAB, the connecting rod BC, and the…

A: for the Given mechanism  To determine  value of θ when Q = 4P

Q: When the 0.05-kg body is in the position shown, the transitional spring at O is pretensioned so as…

A: Given data as per question Moment at spring =0.75 N.m=0.05 kgw=mgRC=0Taking moment aout point…

Q: The spring of modulus k = 870 N/m is stretched a distance ō = 71 mm when the mechanism is in the…

A:

Q: The 1020-kg car is being lowered slowly onto the dock using the hoist A and winch C. Determine the…

A: Given data Mass of the car (M)=1020kg

Q: of constant k is unstretched when the ass m passes position B. If the slider is com rest in position…

A:

Q: 2 -Determine the magnitude ( P) of the horizontal force required to initiate motion of the block of…

A: a) When P is applied to the right, The FBD of bar AB is drawn as,

Q: The lumbar portion of the human spine supports the entire weight of the upper torso and the force…

A:

Q: - Determine the force P required to maintain the 150-kg engine in the position for which 0 = 20°.…

A:

Q: motion of the block of mass ( m.) for 2 -Determine the magnitude ( P) of the horizontal force…

A:

Q: A puck weighs 8 lb and rests on the center of the frictionless surface of the ramp supported in…

A:

Q: The loading device is useful in handling 55 gallon drums. Determine the force F necessary to hold a…

A:

Q: P) For the given pulleys compound system : (a) Find the ldeal Mechanical Advantage (IMA) (b) The…

A: Given information: Let the applied force = F let the forces at the pulleys be labeled as below:

Q: The system consists of the two smooth spheres, each weighing 3 lb and connected by a light spring,…

A: Weight of each ball = 3 lb Force F = 10 lb

Q: When the 12-kN load and the unknown force P are applied, the cable assumes the configuration shown.…

A:

Q: The winch cable on a tow truck is subjected to a force of T = 8 kN when the cable is directed at =…

A: T=8kN

Q: a b c d h     3     2     2 in     3 in     2 ft     The assembly shown has the dimensions given…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.