The shallow foundation shown in Figure 6.25 measures 1.5 m × 2.25 m and is subjected to a centric load and a moment. If eB = 0.12 m, eL = 0.36 m, and the depth of the foundation is 0.8 m, determine the allowable load the foundation can carry. Use a factor of safety of 4. For the soil, we are told that unit weight γ = 17 kN/m3, friction angle ф′ = 35°, and cohesion c′ = 0.

The shallow foundation shown in Figure 6.25 measures 1.5 m × 2.25 m and is subjected to a centric load and a moment. If eB = 0.12 m, eL = 0.36 m, and the depth of the foundation is 0.8 m, determine the allowable load the foundation can carry. Use a factor of safety of 4. For the soil, we are told that unit weight γ = 17 kN/m3, friction angle ф′ = 35°, and cohesion c′ = 0.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.1DP

See similar textbooks

Similar questions

the bod is 17mg/l
A uniform bar is connected to a tapered rod 2. Both are subjected to axial loads as shown . If P = 7kN Determine the axial deformation of uniform bar 1 (in mm) Indicate negative sign if compression. Complete solution no round off.
IA uniform bar is 1 connected to a tapered rod 2. Both are subjected to axial loads as shown . If P = 7kN Determine the axial deformation of rapered rod 2 (in mm) Indicate negative sign if compression. Complete solution no rounding off.
11 - Which is not the spring / spring type used in rail vehicles? A) HelicalB) TorsionC) with collarD) ElastomerE) should be sprained
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown . If P = 7kN Determine the axial deformation of rapered rod 2 (in mm) Indicate negative sign if compression. Complete solution no rounding off.
please answer asap! THEORY OF STRUCTURES (THUMBS UP WILL BE GIVEN. DO NOT ROUND-OFF. WRITE THE COMPLETE SOLUTIONS AND FBDs. BOX THE FINAL ANSWER. NO LONG EXPLANATION NEEDED.) For the beam loaded as shown, determine the reaction components using the Method of Least Work. Use E= 200 GPa, I = 800 x 106 mm4 when & where necessary. Let P = 185 kN
Another of the steel components manufactured by michael's company is steel railway track sections. Thecomponent has a length of 120m (at a temperature of -10°C) and is to be exposed to a temperaturerange of -10°C to 55°C. In order to calculate the gaps which need to be left between the sections michael'scustomer needs to determine the maximum length which each railway track section will expand to andmichael have been asked to carry out the calculation for them. michael have also been instructed to determinethe percentage change in volume and surface area when exposed to the same initial and finaltemperatures. The customer has informed him that the cross sectional profile of the railway track isrectangular and of breadth 14cm and height 32cm. Assume the coefficient of thermal expansion ofsteel is 12x10-6 /°C. Briefly discuss the changes that occur with in the steel as a result of the change intemperature.
Determinoe the masximum tension in th ecable shown
A structural plate component of an engineering design must support 207 MPa in tension. If aluminium alloy 2024-T851 is used for the application, calculate the the largest internal flaw size that this materials can support. given Y=1 ,K1c =26.4
128) With which test is the fluidity of metals measured?A. hardnessB. ViscosityC. CharpyD. SpiralE. Jominy 137) Which is not one of the alloying elements used in steel production? a) Molybdenumb) Aluminumc) Manganesed) Chromiume) Vanadium
diamater bar AB is 22in
The parameter COD is: a. Usually less in value than the ulitmate BOD b. Usually equal in value to BODS c. None is valid d. Usually greater than BODS Clear my choice