in the conduit diagram shown in figure 17-3 determine how many wires are in each conduit between each piece of equipment.identify each wire terminal connection and quantity of wires above the disconnect switch

Q: PVC bends must be made so that the conduit remains undamaged and the internal diameter of the…

A: Bends shall be so made that the conduit will not be damaged and the internal diameter of the…

Q: In the TIA 568-B wiring standard, the colors white green and blue have the pins numbers and O 3 and…

A: In the TIA 568-B wiring standard, the colors white green and blue have the pins numbers

Q: 19.a. The easiest place to install an ammeter into a stepper motor driver/motor circuit for system…

A: Given: The objective is to choose the option that represents the easiest place which is used to…

Q: Question7: Suppose that an electromechanical relay has a coil voltage rating of 5 volts, and a coil…

A:

Q: Draw the ladder diagram of the given relay diagram

A: Two relay logic diagrams are given. We need to draw the ladder diagram.

Q: A plug and connector used for cable termination is identified as 6P6C. The "6C" indicates that the…

A: In the case of 6P6C,  6p represents "conductor Positions", whereas  6c represents  Conductors…

Q: The NEC does not require a separate overcurrent protective device or disconnect when a power factor…

A: Capacitors are used for power factor correction of motors so that more reactive power demand can be…

Q: Analyze and discuss different types of Air blast circuit breakers. Explain with the help of neat and…

A: To overcome the disadvantage of oil circuit breakers air blast circuit breakers are adapted. In oil…

Q: The easiest place to install an ammeter into a stepper motor driver/motor circuit for system…

A: Four options are given in the question. We need to choose the correct option that represents the…

Q: Write an Arduino code to control two LEDs using a push button, given the bellow setup: LED 1 is…

A:

Q: Type UF cable, buried underground, fed from a 15-ampere, ground-fault circuit interrupter at a…

A:

Q: 8. You've just completed a large structured cabling installation and notice that in a bundle of…

A: According to NEC (National electrical code) , in the installation  of cable structure , unmarked and…

Q: Discuss different types of Air blast circuit breakers. Explain with the help of neat and clean…

A: The air blast circuit breaker, according to the type of flow of blast of air is of three types. 1.…

Q: The neutral point of a 11 kV alternator is earthed through a resistance of 12 ohm. the relay is set…

A: We have an alternator which earthed through a resistance and we have been asked to find, Percentage…

Q: An overcurrent relay set to operate at 8A is connected to the multi ratio CT with a 100:5 CT ratio.…

A: Introduction: Current transformer (CT): A current transformer is a device that converts current from…

Q: Duct banks for medium- and high-voltage feeders are identified with _______ on top before final…

A: In this case, the identification of the duct banks with medium and high voltage feeders needs to be…

Q: 16.a. Intersystem bonding terminations must provide a connection point for _______ or more bonding…

A: Note: According to guidelines we need to solve only first question. Please submit a new question…

Q: Determine the time of operation of a 5 A, 3 second overcurrent relay having current setting 150% and…

A: Current setting of Relay is given equal to 150% and CT ratio of 400/5. Here, we can see CT has…

Q: Which type of Insulator is used in Substations to support connections for High Voltage Switchgears,…

A: Given To determine which type of insulator is used in substation

Q: Due to the effect of the resistance of the cable connected to RTD, two-wire cables up to ……. meters…

A: c) 50-195

Q: Discuss how the rating of a circuit breaker is determined and how its operation is coordinated with…

A: Circuit breaker: An electrical circuit breaker is a switching device that may be used to manage and…

Q: 14.a. Section 250.94 requires that an IBT be accessible for inspection and termination and have the…

A: 14.a. IBT stands for Intersystem Bonding Terminal. According to NEC Section 250.94 (B) An IBT be…

Q: THREE-PHASE LINE L1 L3- DISCONNECT SWITCH PRESSURE SWITCH STARTER THREE- PHASE MOTOR Fig. 1-3

A: The circuit is shown below: Between the three-phase line and the disconnect switch. The switch is…

Q: NEC identifies ____ types of rigid PVC conduit. Select one: A. FIVE B. TEN C. THREE D. TWO

A: To discuss the types of rigid PVC conduit identified by NEC.

Q: What is the difference between Shunt and Series Stub? 2. The stub is used to produce pure resistance…

A: As per our policy, i have attempted 3 parts. 1) Difference between shunt and series stub Shunt stub…

Q: Choose the correct Answer: In the TIA 568-B wiring standard, the colors white green and blue have…

A: In the TIA 568-B wiring standard, The pin has following color   Pin 1: White/OrangePin 2:…

Q: | V= C- --- )v 22 2A Answer:

A: The equivalent circuit with assumed directions of current in each resistor and assumed voltage at…

Q: 17.a. How many system conductors are in a high-leg delta system? A. Four B. Three C. Two D. One

A: According to guidelines we need to solve only first question. According to the question we have to…

Q: The horn circuit is being discussed. Technician A says if the circuit does not use a relay, the horn…

A: The simple problem on the Electonics subject. the topic is of relay operation from electrical…

Q: Generators can be connected to the electrical system of the residence in several ways (Select all…

A: Generators can be connected to the electrical system of the residence in several ways

Q: Draw the necessary wire connections to build the circuit shown in this ladder diagram: Ladder…

A: A ladder diagram is shown in the question. We need to draw the necessary wiring connections to build…

Q: 14 Which type of Insulator is used in Substations to support connections for High Voltage…

A: Which type of insulator is used in substations to support connections for High voltage switchgears,…

Q: Calculate the operation time of an overcurrent relay of (10 A , 3 seconds) that has a current…

A:

Q: If the fault current is 2 kA, the relay setting is 50 % and the CT ratio is 400/5, then what is the…

A: Given: fault current=2 kARelay setting=50 %CT Ratio=400/5

Q: It is often desirable in designing an electric wiring system to be able to control a single…

A: The diagram is shown as

Q: alculate the operation time of an overcurrent relay of (10 A, 3 seconds) that has a current setting…

A:

Q: Check the correct statements. * APU supplies DC power to DC bus 1 IDG1 and 2 are placed in parallel,…

A: Given statements about the APU APU supplies DC power to DC bus 1 IDG1 and 2 are placed in parallel,…

Q: 18. Why are signals that are in quadrature said to be orthogonal? A. They do not interfere with each…

A: The detailed answer is solved below according to the given parameters and instructions.

Q: Sump pumps and fill tanks have different wiring requirements for control components.

A: Control components are those components that can regulate a device or electrical components .…

Q: volt,(122V) relay has an inrush rating of 700VA and a hold-in rating of 150VA. Note X1=122V…

A: In this question we will find holding current and inrush   current of relay ...

Q: 7. The size of the supply-side bonding jumpers for each of the individual raceways in the parallel…

A: NEC: NEC stands for National Electric Code. It is a regulatory body that set standard for safety…

Q: Question 3: Compare the impedance characteristic (figure 2) and the mho characteristic (figure 3) of…

A: DISTANCE RELAY: Operating force and restraining forces depend on the system quantities. Impedance…

Q: Problem 2. What is the countering sequence of the following circuit? Is it an asynchronous counter…

A:

Q: C.1. If project documentation is not available, the standard mounting height used for receptacles is…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: An 11 kV, 100 MVA alternator is provided with differential protection. The percentage of winding to…

A:

Speed control of motor

Speed control by DC motor-speed controller is required to realize variable speed drive. Whenever a motor drives a particular load, it is called drive, and variable speed drive refers to a load requiring variable speed. All this is obtained by a DC motor speed controller.