Voltage divider

The micro-controller will be used for sensing the battery voltage and the generator voltage and then switch on/off the DC loads accordingly. The top priority task is charging the battery, so it is given the first preference. After that, the additional power is used for loads. The switches on the load side are implemented using

were assign a group project that demonstrated the knowledge we had gained throughout the entirety of the course. Although we had the option to choose from the following three detention circuits: a resistor-thermistor voltage divider circuit, a phototransistor-resistor voltage divider circuit, or a standard PC microphone driving the audioInput of the myDAQ, my group opted out towards the PC microphone detention circuit. Within the PC microphone detention circuit, the microphone should have been able

difficult. The majority time on this lab was spent on configuration of the pins, rather than writing the code.   Questions and Discussion: What is Rmax and Rmin for your CdS sensor? What is the required resistance, R, for the other half of the CdS voltage divider circuit? The CdS resistance measured in full light was approx. 50 ohms. The resistance measured in a dark lit area was approx. 350k ohms. The range

the two probes are open the voltage of the input is pulled up to the level of Vout. When the behave short circuited or closed, the input voltage goes to ground. see the figure and relate. Pull-down concept:- Now pull-down concept and pull-down resistor works in the same way as in pull- up concept but the resistance is connected to ground. It holds the logic signal near zero volts when the two probes are open circuited. Voltage divider circuit concept:- A voltage divider circuit is a electronic's

backing to this prerequisite. To fill the crevice, in this paper, we propose a framework permitting OSN clients to have an immediate control on the messages posted on their dividers. This is accomplished through an adaptable standard based framework, that permits clients to tweak the sifting criteria to be connected to their dividers, and a Machine Learning based delicate classifier consequently naming messages in backing of substance based separating. Record Terms—On-line Social Networks, Information

Name Institution Course Instructor 10 February 2017 Lab Report: Ohm’s Law & Series Circuits Introduction Theory: Ohm’s law defines the relationship between three important electrical properties namely: voltage, current and resistance. Mathematically, ohm’s law is expressed as: V=IR. By understanding the importance of conduction, one is able to determine the total resistance and visualize how resistors are connected in parallel circuits. In parallel connection, each resistor provides a separate

Future Expansion: This project could also include a multimeter and curve tracer. It could also be improved by having a higher voltage and a better regulated power supply. The function generator could also have higher bandwidth and frequency. Cost: Estimated total cost is $316. Introduction: When we visualized our senior project, we decided that engineering and electronic

resistance. The current is the flow of electrons; the current is dependent on the amount of voltage, which is applied. Voltage is the push given to the current. The current has to go through a circuit, which contains resistance so if you increase that push you also increase the flow of the current. All materials have a slight resistance to electricity factors affecting the resistance are: Length, Voltage & Temperature and Surface Area Length The diagram shows the happenings of

SCHOOL OF ELECTRICAL and ELECTRONIC ENGINEERING Bachelor of Engineering Technology in Electrical Services Engineering Program Code: DT083 YEAR 4 Module: Electrical Plant 2 Lecturer: Thomas Woolmington Student Name Karl Kidd Student Number D02127276 Class Group A Assignment 1 Assignment title: Design of a Standby Generator Date issued 12/2/16 Due by Date returned DECLARATION I hereby certify that the material, which is submitted in this assignment/project

circuit | electrical circuits | mains wiring. Available at: http://www.diydoctor.org.uk/projects/ringmain.htm (Accessed: 1 November 2016). Nature of AC voltage and AC current An alternating current (AC) will describe how the charges of electricity is able to travel in either direction when it is necessarily needed. This alteration changes the voltages and causes it to go back in reverse in the way the current does. - Contributors (no date) Alternating current (AC) vs. Direct current (DC). Available