homework

topic: rigid bodies

HW #4.pdf -> The University of Dlyala Course: Engineering Mechanics i CE 101 College of Engineering Instructor: Dr Assal Hussein Department of C Engineering Homework #4 Replace the loading system by an equivalent resultant force and couple moment acting at point A 900 N 300 N Z00N m 300 N-m 0.75 m T0.75 m075 ma75 m II

Instruction: (Mechanics of Deformable Bodies) • Construct the shear force and bending moment diagrams for the beamshow n by the area method. Neglect the weight of the beam. • On clean sheets of paper write the problem statement, figures and free body diagrams, and complete solutions and final answers. Provide clean, readable, and understandable solution.

er Engineers: El X dXGr5FXCENdllpHQzzLvM_oCLpBbBinmD4RvO_nqWeFros9A/formResponse Solve for the Center of Gravity of the figure below. 4 cm 1 cm 4 cm 2 cm 1 cm 1.5 cm 1cm From the Origin, X = 1 cm 1.5 cm 2 cm 2.5 cm Other: Clear selection 20

Solve Part 3 and Part 4 only

PRESIDENCY UNIVERSITY AZIMUR RAHMAN SCHOOL OF ENGINEERING ENCY DEPARTMENT OF CIVIL ENGINEERING UNIV EVENING AND DAILY PROGRAM COURSE CODE: CE131 COURSE TITLE: ENGINEERING MECHANICS Section:7 FINAL ASSESSMENT: SPRING-2021 TIME: 1 DAY FULL MARKS: 40 Read the question carefully. The figures in the right margin indicate full marks. 1. What is concentrated force? 2. What is rigid body equilibrium? 3. Draw 3 types of support systems with their reaction. 4. Write a short note about rigid body mechanics. 5. Write down the analytical solution method of truss 6. What are the basic differences between statics and dynamics? 7. Differentiate force system based on line of action. 8. In the following picture if anti-clockwise direction is positive then what is the moment arm and value of moment from A point. F A 9. Write a short note about equilibrium co-planner parallel forces. 10.Write a short note about couple.

What is the section modulus of a tube with a diameter of 100mm measured from the outside and has a thickness of 20mm. Use whole number in mm^4. *

Task 1 The engineering department has developed the following equation for the bending moment of a beam and you have asked to investigate its behaviour M(x)=x²-3x²-4 The Beam is 4m long and the design team suspect the is problem if the bending moment is zero in the range between 3-4m and you have been asked to a) Plot the bending moment at 0.5m interval for the range 0≤x≤4m 0≤x≤4 and determine if the bending moment is zero in range 3m ≤ x ≤ 4m b) Use the graph to estimate where the bending moment is zero c) Use the bisection method to numerically estimate the exact location where the bending moment is zero d) Newton-Raphson method to obtain the required location e) Compare the results of the above method to determine which gives a best solution

HW #4.pdf -> The Univenity of Dyala College of Engineerng Department of C Engineering Course: Engineering Mechanics i CE 101 Instructor: Dr Assal Hussein Homework #4 Replace the loading system by an equivalent resultant force and couple moment acting at point A 30N 00N 300 N 300Nm 075 m 10.75 m075 mT075 m II

Lecture: Engineering Mechanics - Couples

subj: mechanics of deformable bodies course: BS in Civil Engineering

subj: mechanics of deformable bodies course: BS in Civil Engineering

Solve this early all subparts. I upvote definitely

PLEASE ANSWER THIS QUESTION ASAP!!!

landscape orientation without erasures 1. The cross section shown in the figure is a structural member known as a z- section Compute the following: (1) cross sectional area, (2) centroidal moment of inertia,Ixo And (3) centroidal moment of inertia, Ivo 3/4 3/4 3.5 Yo 2.625 -3/4 1.375 3.5 -X₂ 113/4

1 KN 4 KN 2KN 5 KN/m -70 CM 40 CM -70 CM 40 CM+-40 CM 60 CMH SUPPORT SUPPORT

Chapter 2, Problem 2/086 Five forces are applied to the beam trolley as shown. Determine the y-coordinate of the point on the y-axis through which the stand-alone resultant R must pass if F = 6.8 kN and 8 = 20°. Point O is at the center of the I-beam. 2.4 kN - 630 mm 70 mm 2.2 kN T 350 mm 1.0 kN 1.4 kN Answer: y = mm the tolerance is +/-2% Click if you would like to Show Work for this question: Open Show Work

bonus question

Hello, Would you please provide a free body diagram for the attached problem.

Subparts: c & d. Please write it on paper.

100% 6 / 10 Semester - ** **** Page 5 of 10 Find the reactions at the supports for the beam that weighs 10 kN shown below. The length of the beam is 10m. B3 20kN 15kN |12kN 2m 2m 2m SAMSUNG OFANTECH F9 F10 F1 F12 PPUFE BROKSPRCE HOME PGUP DELETE END POON ENTER

Question 1. Specify the forces applied to the beams of the beam structure and the load patterns of the horizontal bar BDF. Question 2. Calculate the cutting force developed by the cutters shown in the picture, as well as the force applied to the hinge pin cutting force: (10kp = 100N)

贪ll docs.google.com/forms -27.5 lb None of the above The magnitude of the resultant of two forces of 100 N and 150N acting at an angle of 45° is 232 N 223 N -232 N -223 N none of the above A system of forces is acting on a rectangular plate, as shown in the figure below. The direction of the resultant force with x-axis is * العربية الإنجليزية