CarlyHribar_EET113_W2_LabAssignment3

Part 2: Analysis and selection of the Wind Turbine. The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. 1. Decide on the required number of wind turbines needed. 2. In your own words, explain what the Betz limit for wind turbines means.

-

Which level(s) of measurement is(are) considered qualitative? * Ratio and Interval Interval and Nominal Ordinal and Nominal Ratio and Ordinal

In your own words and from your own understanding, avoid plagiarism or copying from the Course Material, explain or describe MOLDED CASE CIRCUIT BREAKER.

Please answer in typing format with explanation

The system having ±0.5% of F.S.D if the full scale deflection is 50 units, then accuracy is _____ a. ±0.25 b. ±1 c. ±0 d. ±0.5

TRUE OR FALSE? Prior period error are corrected current and prospectively.

A load of 120 MW at a power factor of 0.65 lagging can be delivered by a 3-phase transmission line. The voltage at the receiving end is to be maintained at 63 kV and the loss in the transmission is 6 % of the power delivered. (Consider the line to be a short transmission line) Find Single phase Power delivered Per phase voltage Current flowing through the transmission line 3 Phase Losses in the transmission line Per phase resistance of the transmission line

Can you finish the Background including a synopsis of the relevant information of this this example "electrical maintenance and repair" And please cite an article or paraphrase of author. Thank you! The electrical wiring and electrical devices in the houses that are installed may have failure so the inspection is designed to definitely perform the clear capabilities. These electrical devices are...

22. Determine the standard deviation of the height of trees in meters with the data values 5, 4, 8, 9, 9, 14, 6, and 12. (Round off your answer in 2 decimal places and without unit)

KINDLY ANSWER THESE THREE QUESTIONS. THANK YOU AND PLEASE PROVIDE EXPLANATION

Good day, sir/ma'am. Here is the final question which I require assistance with. Thank you very much. Question: A power transmission line is made of copper 1 .80cm in Find the resistance of one mile of this line.

1. one of the three terminals of a FET  analogous to the base of BJT IS _______

Select the best answer from multiple choices:

AA Health and Safety Mr Ali Lilo, AL4510222L Time remaining: 53 Quick Select QuestiBintaseconds three of the following items of information are required when completing a RIDDOR form? 1 Date & time of incident 2 Type of accident 3 Organisation details. 4 Employer public liability insurance a) 3,2,4 b) 1,4,3 c) 4,2,1 d) 2,3,1 Prev Next actclass.co.uk Questi 22 Questi 23 Questi 24 Questi 25 Questi 26 Questi 27 Questi Submit Answers

Subject : Electrical Engineering

Q1/ Answer by True or False and correct the false sentence: 1- Wire.begin() is used to initiate the wire library in the slave board. 2- In I2C, the clock frequency in range of 50000 to 300000 Hz. 3- Common Ground means the grounds of each board should be connected with each other 4- Pins 0 and 1 are used for external interruption. Solve all please 5- Interruption mode (rising) means: wherever the pin is low. 6- The function getkey () is used to read the size of the array. 7- The segment display is connected only by a common cathode. 8- Delay functions can be used in external interruption. 9- Pin VCC is used to control the LCD display contrast. 10- Serial functions are used with I2C communication.

Explain each option & Choose the correct option. 4) The _ calculated load is rarely placed on an electrical system.A. optionalB. standardC. total 5) What's the primary disadvantage of using copper conductors?A. CostB. AvailabilityC. Weight 6) You're evaluating the components of a multioccupancy building that won't have an on-site employee. To be compliant with the NEC, each occupant will need to have access to their ownA. service-disconnecting means.B. service conductor.C. cable attachment point.D. emergency fire water pump disconnect ..

"A 75-ohm load terminates a 50-ohm transmission line. The point of reflection is at the load. If the measured incident voltage at the point of reflection is 10 Vrms, what is the total voltage at the load? Enter only the numerical value. No need for the unit. Use four decimal places (if the answer is not an integer)."

a.1. A main bonding jumper must only be foundA. within enclosures serving as sub-panels.B. at the grounding electrode.C. on the load side of a GFCI.D. within the enclosure that houses the service disconnecting device.a.2. Which of the following statements about grounding electrode conductors is true?A. They restrict the ground connection.B. They eliminate potential differences between conductive objects and the Earth electrode.C. They facilitate operation of overcurrent protective devices.D. They perform bonding between the Earth and grounded conductors.a.3. Main bonding jumpers are required to be made of _______ or other corrosion-resistant material.A. brassB. aluminumC. copperD. copper-clad aluminum

The arrow in the symbol for n-channel JFET points __ the source-drain connections. Choose the correct answer below: a. can’t be determined b.toward                  c.diagonally                           d.away

An isolator is used to: Select one: a. To be mounted on towers for insulation purpose b. All of the above c. to disconnect part of the system for maintenance from live circuit d. Insulate the wires to avoid electrocution and short circuits Clear my choice

If an electrical system operates at a potential higher than 600 volts, the nonmetallic conduit must be encased in at least_of concrete. A. 1 inch B. 2 inches C. 4 inches D. 6 inches

11. Which of the following statements about the use of structural steel as an equipment grounding conductor (EGC) in an AC system is correct? A. Structural steel can be used as an EGC when it's bonded at both ends.B. Structural steel isn't allowed for use as an EGC.C. Structural steel must have an EGC bonding jumper every three feet of structure. D. Structural steel can be used as an EGC bonding jumper between panelboards. 12. Which of the following statements about equipment grounding conductors is true? A. They increase voltages above ground potential on conductors and equipment enclosures during normal operation. B. Unacceptable equipment grounding conductors include conduit, tubing, and cable armor. C. They must be capable of withstanding the higher level of ground-fault current to perform their safety function. D. When they're far from their associated circuit conductors, impedance values are kept as low as possible during ground-fault conditions. 13. Imagine that…

What is the total number of systems?

And ID No : 510221

Untitled form Your email address will be recorded when you submit this form. Not eng.refcon.k2324@sadiq.edu.iq? Switch account objective question(jW Jlgs) For the circuit shown below choose the correct answer V2 Vi SA 220 300 25A In 31

The __________ audio file format is limited toelectronic musical instruments and other electronic equipment.

17. Which chapter of the National Electrical Code covers communications systems installations andequipment, which have grounding and bonding rules that provide different safety benefits?A. Chapter 5B. Chapter 6C. Chapter 8D. Chapter 7

A protective put can be used for risk management.   A. TRUE B. FALSE