SNIFFY Student instructions

Define FACTS and write its necessity and benefits. With neat diagrams, briefly describe different type of FACTS controllers. Describe SVC and STATCOM and compare their performance.

Draw the schematic diagram of CRT and label the parts. B I II

8. An 8-bit ADC with a 10.0 V reference has an input of 3.637 V i. Determine the digital output. ii. What range of input voltages would produce this same output? iii. Suppose the output of the ADC is 101101012, calculate the input voltage.

What is controlled in a cleanroom? What are the limits? What is the difference between a fab and a cleanroom? Do we need a cleanroom to make a chip? Why?

Q:what is the addressing mode for the following instruction: MOV .(C910), A direct mode O Relative mode O indirect mode O immediate mode O

Q) In measurement system, which of the following static characteristics are * ?desirable Ll 5 Accuracy. All of above. Sensitivity. Resolution.

1- Using the simulator gnusim8085, write a program, which exchange of the contents of (B reg.) to the contents of the accumulator (A reg.) 2- Implement the following programs : Get a byte from monitor ROM : Store it in register D : AND 2880H in RAM : Stop : Load H and L from monitor ROM : Store H and L in RAM a- LDA 2850H MOV D, A STA 2880H HLT LHLD SHLD 2850H 2870H b- : Stop : Put 12H into register H, & 34H into register L : Put 56H into register D, & 78H into register E : Swap DE with HL : Stop : Store the MS sum byte : Stop HLT H, 1234H C- LXI D. 5678H LXI XCHG HLT MOV M,A HLT

I need answer within 20 minutes please please with my best wishes

Design an interfacing system for solar controller, your design should monitor the solar system data like solar panels output, energy consumption, battery charging current, etc, the system must have keypad input and LCD display to allow users to view system status and adjust system parameters like max charging current, max consumption load. ...Draw a detailed block diagram of the interfacing system showing all the signals

Assignment Statement 01: Briefly discuss about different fast charging protocols. Your paper must contain Working principle of fast charging. Difference between fast charging and normal charging. Analysis on the differences between different fast charging protocols. For example- How Dash Charging (used by OnePlus) is different that Adaptive fast charging (used by Samsung). Safety Issues. Your take on this technology.

What is mean by phase angle control method?. Differentiate Natural and forced commutation method. Is it possible to construct rectifier circuits by MOSFET? Justify.                                           ( short anser only plases )

i need the answer quickly

Pls help.me answer the following, show neat and whole solution and kindly send a screenshot of simulation.

2

Draw the schematic diagram of CRT and label the parts.

Ex. 2110. Refer to Figure 2110. Assume MKS units. Given: V4=15/_ 0.30, XL1=16, R2= 4, 15= 3/ 1.40, and XC3=18. Determine V3/ ThV3. ans:2

Q3) Explain the function of the LOOP instruction and write a small program using it (different from the examples in the 8086 emulator program). im

Chapter # 3 Integrated Circuit Technologies Q. Use Table below to explain why the circuit of Figure below will not work as it is. How can the problem be corrected? HW # 04 74нсо 7402 B 7402 Y. Input/output currents for standard devices with a supply voltage of 5 V. CMOS TTL Parameter 4000B 74HC/HCT 74AC/ACT 74AHC/AHCT 74 74LS 74AS 74ALS 74F hulmax) 1 HA 1 HA 1 A 1 µA 40 A 20 A 20 μΑ 20 HA 20 uA AL(max) loH(max) lo(max) 1 A 1 uA 8 mA 1 A 100 A 0.6 mA 1 LA 24 mA 1.6 mA 0.4 mA 0.5 mA 0.4 mA 4 mA 0.4 mA 0.4 mA 2 mA 400 mA 1.0 mA 0.4 mA 4 mA 24 mA 8 mA 16 mA 8 mA 20 mA 8 mA 20 mA Electriai Engeg bepatnt verity f ara

Why is the computed standard error less than the tolerance of the resistors which is 5%. Explain why.  Take note: the computer standard error is 0%

In temperature sensing, RTD stands for... a. reverse temperature detectors b. resistance temperature devices c. regression temperature detectors d. resistance temperature detectors

Explain ARM Cortex M4 controller (STM32F407) and compare ARM Cortex processors, e.g. M0,M1,M2,M3,M4 etc

Q3) Explain the function of the LOOP instruction and write a small program using it (different from the examples in the 8086 emulator program).

13. How can be increased the accuracy of the derivatives for linear finite elements in FEM postprocessor?