5-2 Final Project Milestone Two

QUESTION 3 a) b) Briefly describe the following terms for a generic second order instrument response. i. time constant (T) ii. rise time (Tr) iii. settling time (Ts) iv. peak time (Tp) Indicate the following characteristics on the generic second order response given in Figure Q3(b). i. Rise Time ii. iii. iv. Settling Time Min Settling Time Max Settling Time V. Overshoot vi. Undershoot vii. Maximum peak viii. Peak Time Amplitude 4 3.5 3 2.5 1.5 1 0.5 0 0 5 Step Response 10 Time (seconds) Figure Q3(b) 15 20 25

For answers in acronyms use all CAPITAL Letters. For short answer capitalized the first letter of each word/words unless indicated in the questions. For numeric value with unit, 1 space in between.

Note:Please do not handwritten. Also, please write a lot of information in your own words.

For the following activities, draw the network diagram and by using forward and backward pass, determine:- 1. Project duration. 2. Critical path. Preceding Duration Activity (day) 3 Act. A - -- A 4 C A 2 B E C 1 F C 2 D,E F,G G 4 H. 3

Don't need to explain, but please answer all the question. 1. The resistance strain gauge can measure plastic deformation. A) True B) False 2. In order to save cost, the resistance strain gauge can be reused. A) True B) False 3. In the quarter bridge, there is only one strain gauge which resistance value will change. A) True B) False 4. The shell of inertial acceleration sensor is fixed on the measured object. A) True B) False

Schedule of Loads and Basic Calculation — Create a tabulated load schedule of your home.

Write the code in assembly language

You are required to design a mobile robot vacuum cleaner for use within the warehouse, as shown in Figure 1. The robot has to interact with its environment, and to do so, you have to choose the proper sensor for each task of the following: .A Avoiding obstacles اختيار حواجز B. fail-safe (zero-distance) measurement. 3712915, C. Calculating and updating a robot's position. D. Measuring robot heading angle> راس الزاوية Discuss the working principle of each sensor chosen, using a schematic to illustrate your answer if necessary. Answ ناقش مبدا أ العمل لكل مهمة رسم للسفير اذا وجد A differenti vel OR to B. A direes 40° 180 4m cobaltravale in al ommand has a har 50mm. Determine the w m, in Figure 1. (assume the time requi الزمن لكل خطوة R1.76,117 D 3m 5m B E 2m F 3m 1mG A Figure 1. Route of a robot in the warehouse

please answer the questions in terms of electric car

In order to minimize dissipated heat when current flows through a wire, which of the following strategies can be employed? Select one: a. Increase the cross-sectional area of the wire. b. Increase the length of the wire c. Increase the temperature of the wire d.  Use a wire with increased resistivity e. All of the four items above f. None of the four items above   A portable power bank with USB output most probably uses a/an ______ while an Uninterruptible Power Supply (UPS) used to run a computer during a power outage uses a/an ______. Select one: a. DC-DC Converter; Inverter b. rectifier; inverter c. Inverter; DC-DC Converter d. inverter; rectifier   Please answer both. Need help. Thank you.

Write short note on the below mentioned questions, Each question carries one mark. Students has to answer the questions typewritten in the word (.docx) format. Figures / Diagrams, equations and solving of problems should be written by hand. Take a picture of it and attach it inside the word file. a) High Voltages are preferred for Transmission of Electricity. Why? b) Why Generation Voltage Levels are low in the range of 11 kV/ 33 kV etc? C) Why ACSR Conductors are preferred over Copper Conductors? d) Overhead Transmission Lines are preferred for Transmission of Power for Long Distances, why? e) Alternating Current is preferred over Direct Current in Power System, Why? f) Write the Installed Generation Capacity of Sultanate of Oman with current energy share of Conventional and Non-Conventional Energy Sources. g) Why the Capacitance effect is neglected in Short Transmission Line. h) Distinguish between Lumped or Distributed elements in a Transmission Line.

appropriate answer. Statement one The most common causes of death are falls from heights and being struck by vehicles in the workplace Statement two Following HSE guidance should significantly reduce the risk to an individual a) Statement one is correct and statement two is correct b) Statement two is correct and statement one is incorrect c) Both statements are incorrect d) Statement one is correct and statement two is incorrect actclass.co.uk 25 Questi 26 Questi 27 Questi 28 Questi 29 Questi 30 Submit Answers

I need answer within 20 minutes please please with my best wishes

The following problems refer to grounding requirements. Give the source of yourresponses. 1. If they are present, what items are required to be bonded together to form a groundingelectrode system?

Solve for no. 1 with complete solution

Give information regarding the Heading Indicator. >History >Development and Timeline>Application >How it works>Regulations

A Question Completion Status: 3. 9. 8. 9. 10 Moving to another question will save this response. Question 8 Electric field terminates at... Negative charge Positive charge Both positive and negative Neither positive nor negative A Moving to another question will save this response. 2016292120 (1.oof 2016298130pdf To

The variables vary with respect to time is called as ___________________ a. Static characteristics b. Resolution c. Accuracy d. Dynamic characteristics

II- Research how engineers dispose of the waste produced by the generation of nuclear energy. Be specific and provide details. Please cite sources for all research completed while answering this question. Explain in detail regulations and environmental concerns that may apply (include a minimum of three – more is better). Be specific and provide details. Please cite all your sources. Which field(s) of engineering is involved with these disposal Projects? Are these fields of engineering of interest to you? Why or why not. Explain in detail    Answer all 3

The system having ±0.5% of F.S.D if the full scale deflection is 50 units, then accuracy is _____ a. ±0.25 b. ±1 c. ±0 d. ±0.5

GND int LED - void setup () pinMode (LED, OUTPUT) ; void loop () { digitalWrite(LED,HIGH); delay (1000) ; digitalWrite(LED, LOW) ; delay (1000) ; For the following circuit board, the following code was applied to make the LED blink every one second. 1- If the LED was connected to pin 5 and the delay was 3 seconds. Modify the code to accommodate these changes. 2- How does the LED blinking changes between the two codes? 0O UNO - ARDUINO ANALOO IN

I need answer within 20 minutes please please with my best wishes

A load of 120 MW at a power factor of 0.65 lagging can be delivered by a 3-phase transmission line. The voltage at the receiving end is to be maintained at 63 kV and the loss in the transmission is 6 % of the power delivered. (Consider the line to be a short transmission line) Find Single phase Power delivered Per phase voltage Current flowing through the transmission line 3 Phase Losses in the transmission line Per phase resistance of the transmission line