Lab Project 7 Aircraft Lighting Task

Subject : Electrical Engineering

Centennial College - School of Engineering Technology - Toronto ELECTRONICS SHOP PRACTICES CHAPTER 7: SOLDERING TECHNIQUES 7,5 QUESTIONS 1. Which tools will you need for soldering? 2. What type of solder do we call the Eutectic Solder? 3. If the temperature is too high, the is bellow required, the solder joint will appear cold and silvery and will be of the contact may occur and circuit will not work. If the 4. A long and sharp will be of little use when soldering wires or 5. The iron should have a tip to prevent and should have a wattage rating of to Watts. 6. When soldering, apply heat solder will to both, the component lead and much more readily over the copper pad so that the 7. Keep the soldering iron tip and working surfaces wipe only before using and immediately. 8. Do not solder from a heated tip before off the iron. alternate applying the surface. 9. If tips become and wiping to being used. 10. Periodically. the tip from your tool and with a suitable cleaner for your skills.…

subject : Electrical engineering

Airframe Electrical System Question: In general, what factors areconsidered when selecting the proper size of wire? (Textbook: FAA AC 43.13-1B/2B)

8. You're installing type AC cable. The armor coating of type AC cable is allowed for use as an equipmentgrounding conductor (EGC) because of itsA. liquid-tight fittings listed for EGC purposes.B. interlocking ribs that form a complete circuit.C. internal bare bonding strip.D. internal bare aluminum bonding conductor.

1. What is mean by equipment grounding and system grounding? 2. Discuss any two types of grounding methods.

H1. If you need to make a straight connection to splice two conductors (both size 4 AWG) together, whichof the following connection methods should you use?A. A pressure connectorB. A barrel crimpC. A butt crimpD. A wire nut H2. A/An _______ is an insulating tube or sleeve that protects an electrical conductor where it passesthrough a hole.A. expansion fittingB. couplingC. gland nutD. bushing H3. Conductors that are larger than AWG size 8 will come only as a/an _______ conductor.A. aluminumEnd of examB. coveredC. solidD. stranded

Airframe Electrical System Question: By what means should aircraft electrical circuits/wires be protected from excessive current? (Source: FAA AC 43.13-1B/2B)

Part 2: Analysis and selection of the Wind Turbine. The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. 1. Decide on the required number of wind turbines needed. 2. In your own words, explain what the Betz limit for wind turbines means.

Part 2: Analysis and selection of the Wind Turbine.The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. 1. What are the two closed loop control systems that are used generally in wind turbines? How do they work? 2. Calculate the power density of the input power from the wind when the wind is blowing at the rated wind speed at the turbine height. Clearly show your steps in details.

Discuss any two types of grounding methods.

a.1. A main bonding jumper must only be foundA. within enclosures serving as sub-panels.B. at the grounding electrode.C. on the load side of a GFCI.D. within the enclosure that houses the service disconnecting device.a.2. Which of the following statements about grounding electrode conductors is true?A. They restrict the ground connection.B. They eliminate potential differences between conductive objects and the Earth electrode.C. They facilitate operation of overcurrent protective devices.D. They perform bonding between the Earth and grounded conductors.a.3. Main bonding jumpers are required to be made of _______ or other corrosion-resistant material.A. brassB. aluminumC. copperD. copper-clad aluminum

Need help with second question if all that would be helpgul

In your own words and from your own understanding, avoid plagiarism or copying from the Course Material, explain or describe MOLDED CASE CIRCUIT BREAKER.

Please solve question no.6 and show a clear and readable solution. Choose the letter of the correct answer. Thanks!!!

This discussion relates to Bonding. Whys is bonding of the conduit necessary when using reducing bushings to properly match a conduit to the size hole? Be sure and cite the code reference to back up your answer.

schedules are typically provided to detail the circuits and overcurrent protection required for listribution equipment. Branch-circuit - Outlet C. d. ore distribution points for electrical in .... Switch Panelboard

Building Service Subject

Which of the following statements about equipment grounding conductors (EGCS) is true? A. The National Electrical Code permits the EGC to also perform as a grounding electrode conductor. B. More than one EGC must be used if multiple circuits are installed in a single raceway, cable, or cable tray. C. No current should be present in the EGC during normal operation. D. EGCs are required to be decreased in size to address voltage drop.

Which of the following statements about equipment grounding conductors (EGCs) is true?A. The National Electrical Code permits the EGC to also perform as a grounding electrode conductor.B. More than one EGC must be used if multiple circuits are installed in a single raceway, cable, or cable tray.C. No current should be present in the EGC during normal operation.D. EGCs are required to be decreased in size to address voltage drop.

Electrical Engineering What is the smallest square box that will accommodate four No. 12 conductors and four No. 10 conductors if a. These conductors are pulled through without a splice? b. These conductors are all spliced in the box?

7.A. Ferrous metal raceways or enclosures are made with _______ content.A. steel or brassB. aluminum or ironC. brass or aluminumD. iron or steel7.B. The size of a grounding electrode conductor for a service or separately derived system is generally basedon the size of the largestA. ungrounded supply conductor.B. equipment grounding conductor.C. grounded electrode.D. bonding jumper.7.C. Which of the following statements about bonding is true?A. The joint or termination must offer opposition in the circuit for effective electrical connections.B. Effective bonding keeps impedance high if a fault should occur.C. The entire electrical safety circuit is only as good as its strongest bonded link.D. Bonding connections must endure high levels of fault current until overcurrent protective devices can operate.

Grounding lighting fixtures. Threre are specific requirements for grounding lighting fixtures. How must they be grounded and with what size conductors?

write down the slection of wiring accessories used in electrical installation

NEC identifies ____ types of rigid PVC conduit. Select one: A. FIVE B. TEN C. THREE D. TWO

Raceway fill calculations are a prerequisite in ____ needed for particular circuits. Select one: A. MATERIAL REQUIREMENTS B. SCHEMATIC REQUIREMENTS C. DETERMINING THE SIZE OF RACEWAY D. CIRCUIT LOADS

12. Which of the following statements about ground faults is true?A. They can happen if a conductive tool is dropped in an energized equipment's electrical enclosure.B. They usually occur between any grounded circuit conductor and the equipment grounding conductor.C. They can't result from human error.D. They're often normal and typically intentional.

Can you finish the Background including a synopsis of the relevant information of this this example "electrical maintenance and repair" And please cite an article or paraphrase of author. Thank you! The electrical wiring and electrical devices in the houses that are installed may have failure so the inspection is designed to definitely perform the clear capabilities. These electrical devices are...