Assignment1LabReportEE

2. A full wave rectifier is used to convert 400 Hz ac todc Design a full-wave rectifier power supply that will deliver a dc outpuvoltages 15V and the load current is 1A. RSIT

2. A full wave rectifier is used to convert 400 Hz ac todc Design a full-wave rectifier power supply that will deliver a dc outpu voltages 15V and the load current is 1A. ERS

H.W - For a three phase half wave controlled rectifier with resistive load if the input supply voltage is (Vrms 380 Volt and f= 50 Hz) and the trigger angle (a = 90°), (R-10 S2), Then determine the followings:- 1. Draw the rectifier circuit. 2. Draw to scale the input voltage, the load voltage and the current waveforms. 3. Determine the mean values of the load voltage and load current.

A single phase half controlled rectifier is used to control speed of a dc motor rated at 100V,600rpm. Rectifier is supplied with 220V,50Hz. If the Ra is 0.5 Ohm and La is 6mH. If the motor voltage constant is 0.09V/rpm, armature current is 35A and the motor is working at rated speed. Find a) Back EMF Answer for part 1 b) Vdc Answer for part 2 c) Firing angle in degrees Answer for part 3 d) Power delivered to the motor

Solve it quickly please

A half-wave rectifier with a reservoir capacitor is connected to an AC mains supply(220Vrms, 50Hz) via a 20:1 transformer. What value of the capacitor is needed forthe ripple voltage of X% of the peak input voltage? The load takes a maximum currentof ???? mA. X= 12% mA = 160

a) Explain the operation of the controlled full-wave bridge rectifier shown in figure 3. b) The controlled full-wave bridge rectifier shown in figure 3 has a source 120 V rms at 60 Hz, R = 1092, L=20 mH, and a = 60°. Determine: i. An expression for the load current. ii. The average load current. iii. The power absorbed by the load. iv. Sketch the graph of the output waveform. Vs S₁ S4 Figure $3 $₂ Lo Vo

3. A firing angle controlled triac is feeding a R-L load with L=16 mH and R=12 ohm.The triac input voltage is 220 V rms and 50 Hz. a) Calculate the minimum firing angle at which triac can be fired. b) If firing angle is 27 degress find the angle B at which zero current occurs. c) Find the current 5 msec after firing.

Explain concisely and in your own words the procedure to be carried out for: Vacuum test and Short-circuit test

A- A single-phase half-wave controlled rectifier connected to 120V, 50HZ supply to feed load resistor 52. If the fire angle (a) adjusted to give the maximum output for the rectifier. Calculate and draw the following: a- DC Power b- AC Power c- The rectification efficiency d- Draw the signals (VS, Pulses, V output and VT).

Compute the V2(peak) Half of 2nd windings, Vout(peak), Vout(DC), fout in the center tapped rectifier circuit below: Note: The table shows the values measured using Multisim 10 application

A. Explain the difference between charging current andfaradaic current. B. What is the purpose of waiting 1s after a voltage pulse before measuring current in sampled current voltammetry? C. Why is square wave voltammetry more sensitive than sampled current voltammetry?

(a) Draw the state transition table and the state diagram for the circuit shown in Figure Q1(a). Is this a Moore or Mealy machine? Please justify your answer. JA QA X Yo Y₁ ΚΑ QA' H €1 JB QB KB QB¹ Yo Clock Figure Q1(a)

Tinkercad this or just calculations

For the circuit in the figure below, the supply is 220 Vms, 60 Hz. The load resistance is 16 N. Neglect the Vr of the SCR. a) How much power is delivered to the load if the firing delay angle= 0°? b) How much power is delivered to the load if the firing delay angle= 90°? c) If the firing delay angle= 135°, will the load power be less than one-half or more than one-half of the amount delivered for a 90° delay angle? Explain. RLoad R1 R2 Vsupply SCR

i need the answer quickly

voltages. 2. What design parameters of the full wave single-phase rectifier? 3. When you design 10kW rectifier, what type of rectifier must be use? Why?

2. A full wave rectifier is used to convert 400 Hz ac tod Desa full-wave rectifier power supply that will deliver a dc đ tpu voltages 15V and the load current is 1A. ERS

Discussion and calculations 1. Compare between the practical and theoretical results for input and output voltages 2. What design parameters of the half wave single-phase rectifier? 3. How do you calculate VRM of a half wave rectifier?. 4. How do I know if my rectifier is single phase ? 5. Design a single phase uncontrolled RL half wave rectifier with R=1KQ , L=500 mf and calculate the Vo &lo

Discussion and calculations 1. Compare between the practical and theoretical results for input and output voltages 2. What design parameters of the half wave single-phase rectifier? 3. How do you calculate VRM of a half wave rectifier?. 4. How do I know if my rectifier is single phase ? 5. Design a single phase uncontrolled RL half wave rectifier with R=1KQ , L=500 mf and calculate the Vo &lo

2. A full wave rectifier is used to convert 400 Hz ac tode Des a full-wave rectifier power supply that will deliver a dc dntpu voltages 15V and the load current is 1A. RS!

2b- Please solve this question in detail. Many Thanks   Note: It is preferable by keyboard typing.