19-HW-HP Chebyshev Design ans

Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 200Hz and a higher cut-off frequency of 800HZ. Fa Pau tand Pan Bard Fregarey Lon Pan High Pam Raspon Raspone Figure 1: Band Stop Filter Characteristics Assuming a capacitor, C value for both filter sections (CLP, CHP) of 0.2ur, calculate the values of the two resistors, RuP and Rup using the formula: 1. From the Low pass filter formula, Find RLp: 1 fi = 2. From the High pass filter iormula, Find Rup: 1 fu = 2nRupCuP 3. Calculate the center frequency (fe) and Bandwidth (BW): a. fc = VfL x fu b. BW = fu - fL

Write Legibly. Design a single pole  low pass filter with a gain of 10 in the passband and a 3dB frequency of 5kHz.  The minimum resistance in the passband for this filter is to be of 10k-ohms.  What is the value of C in nF and in two decimal places only.?

Solve it fast plz

Acos (wit) u pass PR ·Vo Is this a low pass or high pass filter and where is the 3dB down point? 6087)

Which of the following is not a part of the PLL O a. Loop filter O b. phase detector O C. Differentiator O d. Voltage controlled oscillator Which of the following statements is not correct: a. A third-order PLL can track a frequency step with zero steady-state error. O b. A first-order PLL can track a frequency step with a zero steady-state error. O c. A first-order PLL can track a phase step with a zero steady-state error. O d. A second-order PLL can track a frequency step with zero steady-state error. %24

Need help steps would be helpful please and thank you!

Frequency (Hz) 100 200 500 1000 2000 5000 10000 20000 50000 100000 Magnitude Response 20log| Vout(jo)/Vin(jo)| Vout(jo)/Vin(jo)||

Design a two-pole high pass Butterworth active filter with curoff frequency of 10 kHzand a unity gain magintude at high frequency.  Find R4 in Ohmc and use two decimal places, below if 0.001 uF.

By using 3 order High pass filter and sallen key Low pass filter design a state variable * ? Band stop filter

Design a two-pole high pass Butterworth active filter with curoff frequency of 10 kHzand a unity gain magintude at high frequency. Find R in Ohmc and use two decimal places, below if 0.001 uF.

Find the critical frequency of this band-pass filter with 1 kHz frequency and an amplitude of 10 V

3. A band-reject filter may be designed by combining a low-pass filter and high-pass filter with a summing amplifier. A 60 Hz signal is to be at least -50dB below the maximum gain value of 0dB as shown below with a two-pole low- pass Butterworth filter and a two-pole high-pass Butterworth filter. What is the bandwidth of the reject filter? IX 60412

Design a single pole  low pass filter with a gain of 10 in the passband and a 3dB frequency of 5kHz.  What is the value of R1?

1. A band-pass filter allows certain frequency bands to pass and can be determined by cut- off frequencies. a. Determine the Fs1, Fp1, Fp2 and Fs2 for the following band-pass filter design in Figure I with sampling frequency of 500Hz, aos 1-0.25x. op1-0.35%, cp2=0.55m and cos2-0.65%. Magnitude 1+4 1-4 6.707 Tration Band Amy M ways Passband wys Frequency Figure 1: Band-pass filter Transition Bod Ayy (=F₂) b. Given the following filter equation, determine the type of the filter. y[n] = 3x[n] + 2x [n - 1] + 3y[n-1] + 4x[n-2] +5x[n-4] c. Give two advantages of IIR filter compared to FIR filter. IN

7) i need fast please now

Determine type of filter and the cut-off frequency (Fc). High Pass Filter & Fc = 9997.17Hz  Determine the peak voltage at the cut-off frequency (Fc) GIven --> Gain = 0.5, --> Vp = 0.5 x 12 = 6V Find GAIN (Vo/Vi) at  f = .1*Fc gain = 0.0995 Find GAIN (Vo/Vi) at  f = 10*Fc gain = 0.99995 Determine the frequency at which GAIN = .4  (i.e., Vo = .4*Vi) f = 4363.12Hz Draw the  “Frequency Response Plot” in “Log-Log” format

Quiq

bls 5 Why the band-pass filter is used in some communication instruments? ?how many stages this filter has

Derive the equation for the order of Butterworth filter and find the transfer function of Butterworth filter with order n=7

Determine the voltage transfer function of the filter circuit shown below and classify the filter as LP, HP, BP or BS. Clearly explain your reasoning. R₁ R Vin A L voo out

kalman filter

Design a 2nd order band pass filter with low cut-off frequency of 500Hz, high cut-off frequency of 10kHz and a passband gain of 5. Plot the frequency response of this filter and find the value of Q for the filter. Comment if it's a narrow band pass filter or wide band pass filter.

Urjant

Response curves for second-order filters are shown in Figure 3. Identify each as Butterworth, Chebyshev, or Bessel. (a) -40 dB/decade (b) (d) out V out -40 dB/decade decade

How to design a 3 kHz Low pass filter (n=2) using the lm741 opamp in Filter Pro?

[Q6] Design a third order filter low pass filter with cutoff frequency using 1- Butterworth approximation 2- Chebyshave approximation 3- Bessel approximation

Explain nicely and write clearly Answer Correctly Completely Answer only if you are sure I will like you on your answer and invite my colleagues also Thank you :)