Lab3_Assignment (1) (2) (1)

.pdf

School

University of Arkansas, Fayetteville *

*We aren’t endorsed by this school

Course

1113

Subject

Geography

Date

Dec 6, 2023

Type

pdf

Pages

7

Uploaded by ChefLemur3909

Report
LAB 3: SEISMIC HAZARDS 100 points Due at the beginning of next week’s lab meeting time. LEARNING OUTCOMES At the end of this lab, you will be able to 1. Understand hazards associated with earthquakes 2. Identify seismic wave signals in a seismograph 3. Use a seismogram to identify an earthquake epicenter INTRODUCTION Earthquakes are the spontaneous release of energy within the lithosphere. Stress applied by tectonic forces becomes potential energy stored in the ground. Most earthquakes are released along faults within the first 25 miles of the Earth’s surface. Sudden movements along faults cause shock waves to radiate away from the focus of movement. Earthquakes are measured with several scales (e.g., Moment magnitude, Richter)—both exponential scales used to quantify the magnitude of an earthquake. Seismic waves transfer energy from one place to another through rock and sediment. P-waves are the first to arrive at a recorder, called a seismometer. S-waves are the second. P-waves travel through solids and liquids, while S-waves only travel through solids. P- and S-waved are used to determine the magnitude of an earthquake. You can use a Richter Nomogram to draw a line connecting the values of distance and magnitude, which require the identification of when the waves reach the seismometer, recorded on a seismogram (Figure 1). The line will cross the magnitude plot showing the value of the earthquake. A seismogram records earthquake intensity. Because P-waves and S-waves travel at different speeds, the lag time (i.e., S-P interval) can be used to calculate how far away the earthquake happened if we know the wave velocities. Figure 1 is a simplified seismogram showing P-wave and S-wave traces. Seismologists use three or more recording stations to locate the epicenter of an earthquake, or the spot on a map below which the earthquake focus is located. The epicenter’s distance from the recording station can be found from a plot of time versus distance. Circles drawn around the recording stations at the proper distance will intersect at the epicenter, where three circles will intersect at only one point, the epicenter. 1
Figure 1. Example seismogram recorded by a seismometer with the wave arrival times and signal amplitudes labeled. The x-axis is Time in seconds with time increasing to the right. The y-axis is the signal amplitude measured in millimeters – this is how much shaking there was at the seismometer. For another example of a seismogram with surface waves, arriving later and with larger amplitude than is shown above, click this link . There are many different hazards associated with earthquakes. Landslides, rock fall, and cracking of the ground are some of the hazards associated with earthquakes. Surface waves (not S-waves) are the most damaging of the seismic waves, especially to buildings not made to withstand earthquake hazards. One of the more hazardous effects of earthquakes is called liquefaction, where sediment behaves like a liquid when shaken. Only certain soils are prone to liquefaction. When these soils are dry, they are stable, although once saturated and a shock is applied, they may lose their internal cohesion. This may cause catastrophic damage to any structures on the surface. 2 LAB 3: EARTHQUAKES AND SEISMIC HAZARDS [100 pts]
In this lab, you will locate the epicenter of an earthquake that occurred in the San Francisco area and calculate its magnitude using seismograms from 3 recording stations, included after the lab questions. The x-axes of the seismograms are in seconds, like in Figure 1. 1a) Identify the arrival times for P- and S-waves in the seismograms. Calculate P-wave/S-wave intervals by subtracting the arrival times and enter the intervals into the table below. [10 pts] 1b) Enter the maximum seismic wave amplitude of each station into the table below. [10 pts] 1c) Using the graph of time versus distance, identify the distance from each station to the epicenter, and enter them into the table below. [15 pts] Recording station S-P Interval (seconds) Amplitude (mm) Distance from epicenter (km) Eureka, CA 275 mm 480 km 50 Las Vegas, NV 65 100 mm 640 km Elko, NV 55 mm 700 km 72 1d) Go to www.iris.edu/app/triangulation . Use the “+Station” function to input the latitude, longitude, and distance from epicenter of each of the recording stations above. Take a screenshot and insert it here. [15 pts] 3
Your preview ends here
Eager to read complete document? Join bartleby learn and gain access to the full version
  • Access to all documents
  • Unlimited textbook solutions
  • 24/7 expert homework help