0.8 m The shown spool has a mass of 450 kg and a radius of gyration k, =1.2m. It rests on the surface of conveyer belt for which the coefficient of friction u =0.5. If the conveyer accelerates at1.2m / Sand the spools rolls without slipping, determine the tension in the wire and the angular acceleration of the spool - 1.6 m

0.8 m The shown spool has a mass of 450 kg and a radius of gyration k, =1.2m. It rests on the surface of conveyer belt for which the coefficient of friction u =0.5. If the conveyer accelerates at1.2m / Sand the spools rolls without slipping, determine the tension in the wire and the angular acceleration of the spool - 1.6 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.87RP: Can the uniform bar of weight W remain at rest in the position shown?

See similar textbooks

Similar questions

Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
if mass (m)=345kg radius of gyration kG = 0.54 m θ= 200 degree 1) assuming no slipping and when starting from horizontal cable (θ = 0o) the spool moves to the left- determine the minimum tension in the cable (Tmin) that causes the spool to slip. Assumeμk = 0.4 and μs = 0.5.
The spool has a mass of 200 kg and a radius of gyration of kG = 0.2 m. If the coefficients of static and kinetic friction at A are μs = 0.3 and μk = 0.2, respectively, determine the angularacceleration of the spool if P = 400 N.
The right‐angle plate is formed from a flat plate having a mass ρ per unit area and is welded to the horizontal shaft mounted in the bearing at O. If the shaft is free to rotate, determine the initial angular acceleration α of the plate when it is released from rest with the upper surface in the horizontal plane. Also determine the y‐ and z‐components of the resultant force on the shaft at O.
Just like the change in momentum over time generates a force (P=F) , the change in ∆t angular moment results in a torque (L = τ) . Using the theoretical values for the moments∆tof inertia of the hollow cylinder and disk, determine the torque done on the system whenthe cylinder is dropped on the disk. Take ωi = 9.5 rd/s, ωf = 6.1 rd/s, and ∆ t = 2 s
The racing vehicle has a mass of 750 kg and center of mass in G. If there is no slippage, determinate the normal reaction, in Newtons, presented on each of the front wheels in A, when an acceleration of a = 6.4 m/s².
The shown spool has a mass of 100 kg and radius ofgyration of 0.3 m. For P = 70 N and ms =mk = 0.2 thespool rolls without sliding, calculate the angularacceleration of the spool
6/40 If the frictional moment at the pivot O is 2 N+m, de- termine the angular acceleration of the grooved drum, which has a mass of 8 kg and a radius of gyra- tion kg = 225 mm. 200 mm kg 12kg
The thin rod in the figure has a mass of 15kg and is attached to a spring of constant k = 50 N / m at one end, which has an unstretched length of 1.5 m. If the rod is released from rest in a horizontal position (ѳ = 0 °) and only conservative forces act on it, determine:a) What is the moment of inertia of the thin rod around the axis of rotation at A? b) What is the angle at which the rod is momentarily at rest again? c) What is the maximum angular velocity of the path?
A barrel of asphalt weighing 450 N starts from rest at Aand rolls without friction along a vertical parabolic curveACB with dimensions L = 6.00 m and d = 1.20 m. Find thenormal force between the barrel and the path at the lowestpoint C. Hint: You need to determine the radius of thecurvature at point C.
The wheel in the figure has a mass of 40 kg and a radius of rotation, in relation to its center of gravity, kG = 250 mm. Whereas there is no slip, determine the angular velocity of the rotates after it rotates 90 ° clockwise from illustrated position. The AB spring has a constant stiffness k = 100 N / m and a length in the undisturbed situation of 500 mm. Consider that the wheel is initially at rest.
The homogeneous cylinder A has a mass of 80 kg, and the mss of the hub can be neglected. The magnitude of the variable force P, is in newtons when t is in sec- onds. The velocity of body B changes from 2 m/s downward when t = 0 to 4 m/s downward t = 5 s. Determine the mass of B. Solve all questions using Impulse and Momentum methods