The 45-kg reel has a radius of gyration about its center O of ko = 220 mm. If it is released from rest, determine the total external work done to it when its center O has traveled 6.6 m down the smooth inclined plane (with angle = 35°). Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point, and proper SI unit. Take g = 9.81 m/s².

The 45-kg reel has a radius of gyration about its center O of ko = 220 mm. If it is released from rest, determine the total external work done to it when its center O has traveled 6.6 m down the smooth inclined plane (with angle = 35°). Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point, and proper SI unit. Take g = 9.81 m/s².

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.26P: The uniform plank is initially at rest on the fixed support at A and the stationary drum at B. If...

See similar textbooks

Similar questions

The body and bucket of a skid steer loader has a weight of 2000 lb, and its center of gravity is located at G. Each of the four wheels has a weight of 100 lb and a radius of gyration about its center of gravity of 1ft. If the engine supplies a torque of M = 100 lb ft to each of the rear drive wheels, determine the speed of the loader in t = 10 s starting from rest. The wheels roll without slipping
The 150-kg pendulum has a center of mass at G and a radius of gyration about G of kG = 0.25m, as shown in Figure 2. Determine the horizontal and vertical components of reaction on thebeam by the pin A and the normal reaction of the roller B at horizontal direction when thependulum is rotating at 5 rad/s. Neglect the weight of the beam and the support. If the normalreaction of the roller B at horizontal direction change to vertical direction, determine thehorizontal and vertical components of reaction on the beam by the pin A.
The pendulum has a mass of 8.8 kg, a centre of gravity at G, and a radius of gyration of 0.31 m about the fixed pin support at O. At what position (in degrees) must the pendulum by released from rest so that its angular acceleration is 18.6 (clockwise) at that instant? Take = 0.25 m. The motion occurs in a vertical plane and friction is negligible. Choose the correct answer. 43.2 36.7 34.6 48.4 41.1
The 3.8 kg block is descending at a rate of 1.2 m/s when the hydraulic cylinder BC exerts a force F=500 N on the brake arm. Determine the number of radians the wheel will rotate before the system comes to rest. The wheel has a mass of 25 kg and a radius of gyration about its center kO=300 mm. The coefficient of kinetic friction between the brake arm and the wheel is 0.25.
if mass (m)=345kg radius of gyration kG = 0.54 m θ= 200 degree 1) assuming no slipping and when starting from horizontal cable (θ = 0o) the spool moves to the left- determine the minimum tension in the cable (Tmin) that causes the spool to slip. Assumeμk = 0.4 and μs = 0.5.
The rod AB has a mass of 20 kg，the mass of the piston A and B are both 5kg. Piston B is attached to a spring of constant k = 1200 N/m. The spring is un-stretched when θ = 0. If the rod is released from rest whenθ = 45° Please find÷ (1) the moment inertia of the rod AB about its mass center G (2)The angular velocity of rod AB at θ = 0° (3）the velocity of piston A at θ = 0° (4) the velocity of Piston B at θ = 0° (hint: regard the piston A, B, rod as a system, during the motion, except the spring, the weight of rod AB, the weight of pistonB also does work). g = 9.8 m/s2
The dynamic system is initially at rest. The rod has a mass of m=0.5kg and a length of L=1m. The CG of the rod is located at G, and the rod is rotated about the point O, a distance, h=0.25m, away from point G. At the time of releasing find a. Acceleration at the CG (point G) b. Reaction at O (Use moment of inertia of the rod I= mL2/12)
The 75 kg wheel has a radius of gyration about its mass centreof kG=400mm. If it is subjected to a torque of M=150 N.m,determine:a. The angular acceleration of the wheel,b. The linear acceleration of the mass centrec. The created frictional force at the point of contact.The coefficient of static friction between the wheel and theground is S=0.3.Hint: Assume no slipping occurs at star, and verify I at the end.
Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
The right‐angle plate is formed from a flat plate having a mass ρ per unit area and is welded to the horizontal shaft mounted in the bearing at O. If the shaft is free to rotate, determine the initial angular acceleration α of the plate when it is released from rest with the upper surface in the horizontal plane. Also determine the y‐ and z‐components of the resultant force on the shaft at O.
The wheel has a mass of 100 kg and a radius of gyration of kO = 0.2 m. A motor supplies a torque M = (40u + 900) N #m, where u is in radians, about the drive shaft at O. Determine the speed of the loading car, which has a mass of 300 kg, after it travels s = 4 m. Initially the car is at rest when s = 0 and u = 0°. Neglect the mass of the attached cable and the mass of the car’s wheels
The spool has a mass of 20 kg and a radius of gyration of kO = 160 mm If the 15-kg block A is released from rest, determine the velocity of the block when it descends 850 mm .