03:bridge rectifier circuit shown in Figure (1), with a forward diode resistanceRd=12, and Rd=0 for a reverse bias. The input voltage of the circuit is 240Vand 482 load resistance. Determine: The de load current, the power inputefficiency and the PIV rating is required for the diodes.D4D1Rd=10RL=480VsVrmsVoD3D2Figure 1

Answered: Image /qna-images/answer/56fc65bd-23b8-4e0a-8e4c-4905bc8f4b1b.jpg

03: bridge rectifier eircuit shown in Figure (1), with a forward diode resistance Rd=12, and Rd=o for a reverse bias. The input voltage of the circuit is 240V and 4892 load resistance. Determine: The de load current, the power input efficieney and the PIV rating is required for the diodes. D4 D1 Rd=10 RL=480 Vs Vrms Vo D3 D2 Figure 1

03: bridge rectifier eircuit shown in Figure (1), with a forward diode resistance Rd=12, and Rd=o for a reverse bias. The input voltage of the circuit is 240V and 4892 load resistance. Determine: The de load current, the power input efficieney and the PIV rating is required for the diodes. D4 D1 Rd=10 RL=480 Vs Vrms Vo D3 D2 Figure 1

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
How is a solid-state diode tested? Explain.
What is CEMF?
In a 1-phase full wave bridge rectifier with Vs = Vm sin ωt, with R load & ideal diodes. The expression for the average value of the output voltage is 2Vm/π Select one: True False
1N4001, 1N4002, 1N4003, 1N4004, 1N4005, 1N4006 and 1N4007 For any of the diodes, describe with the aid of diagrams/illustrations its applications in an AC to DC Bridge rectifier power supply circuit. For your circuit show and describe how you are going to smooth out the ripple voltage that will be present.
How is Zener diode connected into a circuit? What determines the voltage at which a Zener diode break down? What considerations go into determining the power dissipation rating of a Zener diode? Draw a label the schematic symbol used to represent a Zener diode What determines the maximum Zener current of a Zener diode? What is the difference between the maximum Zener current and the reverse current for a Zener diode? What does a positive Zener voltage temperature coefficient signify? What does a negative Zener voltage temperature coefficient signify? How can a Zener diode be temperature compensated?
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary.
A full-wave bridge rectifier with a 236.86V p-p sinusoidal input has a load resister of 2KΩi. Draw the wave form that the load resistor R would see. ii. Assuming diodes are ideal, what is the dc voltage available at the load resistor? iii. What is the dc voltage available at the load if silicon diodes are employed? iv. Calculate the maximum current flow through the Diode D4 during conduction.
1. Draw and briefly explain the ideal characteristics of PN-junction diode ? 2. Explain briefly about avalanche and Zener breakdown ? 3. In which region can Zener diode be used as a regulator? Why? 4. What is the ripple factor? For a good filter, should the ripple factor be high or low? 5. What is a rectifier? What is the difference between a full-wave rectifier and a half-wave rectifier?
Assume that an input signal is applied to the circuit given above, as shown in the figure next to it. Accordingly, answer the following questions. The diodes used are silicon diodes, their operating voltages are 0.7 volts, and can be omitted because their resistance is very small. a) Write the name of this circuit, thinking about which circuit we do in the courses is equivalent to the purpose. b) What are the diodes/diodes that are active in a positive half-loop? Please type. c) What are the diodes/diodes active in the negative half-loop? Please type. d) Calculate ? ?−???( ?? ) for this circuit.
In a center-tapped full wave rectifier circuit utilizing ideal diodes, if the primary voltage is 160Vpeak, the turns ratio is 8:1 and the load resistance is 860 ohms, what is the rectified dc voltage at the output? express answer in volts