1: The parameters of a three-phase line 200 km long are resistance = km=0.15 Omega , inductive and capacitive susceptance km-2*10^ -6 The transmission line is delivering 50 MVA at 132 kV with power factor 0.85 lagging. Use nominal T method to determine; 1) sending end voltage ductive/km=0.5 0mega 2) sending end current 3) sending end power factor 4) %3D

1: The parameters of a three-phase line 200 km long are resistance = km=0.15 Omega , inductive and capacitive susceptance km-2*10^ -6 The transmission line is delivering 50 MVA at 132 kV with power factor 0.85 lagging. Use nominal T method to determine; 1) sending end voltage ductive/km=0.5 0mega 2) sending end current 3) sending end power factor 4) %3D

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.25P

See similar textbooks

Similar questions

Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
A 25 kilometer long three phase transmission line has conductors 2.5cm in diameter and are separated by a distance of 2 meter. The resistance of the line is 4 Ω and it delivers 15MW at 33kV, 0.7 power factor lagging. Estimate i. Inductive reactance ii. Sending end voltage iii. Voltage regulation iv. Transmission line efficiency
A three-phase transmission line is 160 km long and supplies a load of 12 MW at 0.85 powerfactor lagging at 80 kV, 50 Hz. Each conductor has a resistance of 0.275 Ω / km, an inductivereactance of 0.5625 Ω / km and a capacitance to neutral of 0.008625 µF / km. Calculate the line-to-line sending end voltage and the sending end current, using: i. The nominal T method.ii. The nominal Π method. If the sending end voltage remains constant, estimate the approximate rise in voltage at thereceiving end when the load is switched off. Hence calculate the per unit voltage regulation ofthe transmission line.
A 500 kV, 60 Hz uncompensated three-phase transmission line is 500 km long. The line has three ACSR 1113-kcmil (Finch) conductors per phase with parameters Current carrying capability of single ACSR 1113-kcmil (Finch) conductor is 1,110 A. Calculate the theoretical maximum (steady state stability limit) real power that this line can deliver and compare with the thermal limit of the line. Assume VS = VR = 1.0 per unit and unity power factor at the receiving end.
A 220 kV, 50 Hz, three-phase transmission line is 60 km long. The resistance per phase is 0.15 ohms/km and the inductance per phase is 1.3 mH per km and the shunt capacitance is negligible. Use the short line model to determine; i) the voltage and power at the sending end ii) voltage regulation and efficiency when the line is supplying a three-phase load of 350 MVA, 220 kV at a power factor of 0.85 lagging.
Characteristics of 165 kV, 150 MVA, 50 Hz 3-phase 100 km transmission linevalues are given below. r=0.103ohm/ kmx=0.525ohm/ kmy=3.3x10^-6 S/ km (a) Calculate the constants A and B for the equivalent circuit of this transmission line,(b) Load lagging power factor of 0.9 when the line is running at nominal (tag) value.if so, find the production side voltage. lesson: Power system analyses
A 3 phase, 50 Hz, 150 km line has a resistance, inductive reactance and capacitive shunt admittance of 0.1Ω, 0.5Ω, and 3 x 106 S per km per phase. If the line delivers 50MW at 110kV and 0.8 pf lagging, Assume a nominal phi circuit for the line determine: a. Sending end current b. Line value of the sending end voltage c. Transmission efficiency d. Voltage regulation e. Sending end power factor
A power of 90+j70 MVA is drawn from the end of a 220 km three-phase transmission line with a voltage of 380 kV. The following values are given for the line: z = 0.166 + j0.86 Ω/km and y = j6x10^(−6) w/km .Calculatethe sending end voltage, sending end current and efficiency for each of the following cases. 1-)Using short transmission line approximation. 2-)Using long transmission line approximation.
Q1: The parameters of a three-phase line 200 km long are resistance/km-0.15 0, inductivekm -0.5 and capacitive susceptancekm-2x 10° U. The transmission line is delivering 50 MVA at 132 kV with power factor 0.85 lagging. Use nominal T method to determine; 1) sending end voltage 2) sending end current 3) sending end power factor 4) transmission efficiency and 5) voltage (4 points) regulation
A 30 mile, 3-phase transmission line delivers 8,000 kW at 33 kV, p.f. 0.8 lagging. The resistance and reactance of single conductor are 0.6 ohm and 0.72 ohm respectively per mile. Find the voltage at the sending end in kV.
A three phase line 30 km long delivers 2000 KVA at 33 kV voltage, 0.707 lagging power factor. If the resistance of the line is 0.5 Ω per phase per kilometer and the inductive reactance of the line is 0.8 Ω per phase per kilometer, find (1) voltage regulation (2) transmission efficiency and (3) sending and power factor
A (medium) single phase transmission line (Islamabad to Kashmir) 100 km long has the following constants : Resistance/km/phase = 0·15Ω Inductive reactance/km/phase = 0·377 Ω Capacitive reactance/km/phase = 31·87 Ω Receiving end line voltage = 132 kV Assuming that the total capacitance of the line is localized at the receiving end alone, determine : sending end current line value of sending end voltage voltage regulation sending end power factor The line is delivering 72 MW at 0·8 p.f. lagging