Please do all with explanation follow this please 1) True or false with explanation-A) pascal's law says that applying pressureanywhere to abody on fluid causes a force tobe transmitted equally in all directions. (T/F).B) Pneumatic elements are classified intotwo groups. (T/F).C) The total energy increases when thehydraulic fluid flows faster and decreaseswhen the speed of the hydraulic Fluid isreduced. (T/F)

Answer (A) Pascal's law: The force due to the fluid is equally transmitted in all direction at any…

Answered: 1) True or false with explanation- A)…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

29 - Water is drawn from the bottom of a large tank filled with water open to the atmosphere. If the outlet velocity is 7.2 m/s, what could be the height of the water in the tank? a) 2.64m B) 4.38m NS) 3.65 m D) 5.46 m TO) 2.20m 30 - What would be the weight of an object with a mass of 100 kg in a place where the gravitational acceleration is 8 m/s²? a) 42.2 kgf B) 98.1 N NS) 800 N D) 9810 N TO) 196.2 N
Unreasonable Results - A slightly deranged Arctic inventor surrounded by ice thinks it would be much less mechanically complex to cool a car engine by melting ice on it than by having a water-cooled system with a radiator, water pump, antifreeze, and so on. (a) If 80% of the energy in 1.00 gal of gasoline is converted into “waste heat” in a car engine, how many kilograms of 0C ice could it melt? (b) Is this a reasonable amount of ice to carry around to cool the engine for 1.00 gal of gasoline consumption? (c) What premises or assumptions are unreasonable?
P2 Illustrate a proposed solution to a hydraulic problem, using drawings or models.
In general term, ______________ is the tendency of one fluid to spread on to a solid surface in the presence of other fluid a. Relative Density b. Porosity c. Permeability d. Viscosity e. Wettabilty
Fluid mechanics, i need solutions in 10 minutes please. MCQ/ what is the specific weight of the wooden beam? A-44.339 lb / ft³ B-40.842 lb / ft³ C-49.582 lb / ft³ D-55.825 lb / ft³ E-37.342 lb / ft³ F-53.144 lb / ft³ G-30.453 lb / ft³ H-51.330 lb / ft³ I-33.840 »/ ft³ J-47.835 lb / ft³ K-35.591 lb / ft³ L-28.247 lb / ft³ M-42.590 lb / ft³ N-58.631 lb / ft³
Given the sketch shown below, the diameter of the plunger Dp = 8 cm. The Ram diameter is Dr = 48 cm. The efficiency is 100%, the stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2kN. Find: A) the force f1 exerted on the plunger. B) the number of strokes needed to raise the load given above by a distance of 10 cm. C) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) D) what will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8 cm.
If you rent a car, you can (1) return it with a full gas tank, (2) return it without filling it and pay $5.75/gallon, or (3) accept a fixed price of $60 for gas. The local price is $3.50/gallon for gasoline, and you expect this car to get 25 miles per gallon. The car has a 16-gallon tank. What choice should you make if you expect to drive: (a) 150 miles? (b) 300 miles? (c) 450 miles? (d) How do your answers change if stopping at the filling station takes 20 minutes and your time is worth $15/hr?
If a pool is irregularly shaped and a person being assessed has a weight mg= 800 N but weighs Fn= 40N while submerged. Assuming a residual volume Vres= 1.4 L= 0.0014 m^3. a. What is their average density b. What percentage of their body volume would be above water, while floating? c. What is their bodys volume d. How much more buoyant force would they experience with their lungs holding a full six liters? What percentage of thheir body volume would be above water now?
You are to spray an 80-acre field that will be planted to alfalfa with 32 oz/ac Roundup, 1.5 pints/ac of Treflan, and 17lbs AMS/100 gallon spray. If your sprayer is calibrated to apply 10GPA carrier volume and holds 800-gallons how much AMS do you need to add to your sprayer to condition your water, and how many gallons of Roundup and Treflan do you need to add to your sprayer so that you apply the proper rate?
A. The hydrostatic force due to linseed oil F1.B. The hydrostatic force due to castor oil F2. C. The hydrostatic force due to water. D. The net hydrostatic force acting on the gate Fnet
A spherical research balloon is filled with 420 m3 of atmospheric air at a temperature of 10°C. If the air inside the balloon is heated to 80°C according to PVn =C, where n = 0. What will be the final diameter of the balloon? show cancellation of units and formula used
A wave in deepwater has a height of 30 ft and period of 13 s. What is the height of the wave in 100 ft of water resulting only from shoaling?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS