1. Find the physical address of interrupt service procedure for the following interrupt instructions: (i) INT 01H (ii) INT FFH For answering question 1, use the following interrupt vector table. 12 HO0000 34 HT0000 65 00002H F2 00003H 00004H 00005H H90000 00007H 00008H 66 45 H60000 003FCH 003FEH 003FFH

1. Find the physical address of interrupt service procedure for the following interrupt instructions: (i) INT 01H (ii) INT FFH For answering question 1, use the following interrupt vector table. 12 HO0000 34 HT0000 65 00002H F2 00003H 00004H 00005H H90000 00007H 00008H 66 45 H60000 003FCH 003FEH 003FFH

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter6: System Integration And Performance

Section: Chapter Questions

Problem 12VE

See similar textbooks

Similar questions

If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the fetch cycle is 40% of the processor cycle time, what memory access speed is required to implement load operations with zero wait states and load operations with two wait states?
6. Suppose that the interrupt processing method of is to store the breakpoint in the address of 00000Q unit, and fetch the instruction from the 77777Q unit (that is the first instruction of the interrupt service routine) and execute it. Write the micro-operations sequence that completes this function.
QUESTION 2 Discuss with examples the main difference between system programming and application programming and explain in your own words how each of these can be carried out in the computer system. With your knowledge in memory addressing modes and using the given opcodes LDA = 00 0000 0000 (00) 0 (x) What will be the content of the address loaded into the accumulator? b. With your knowledge in memory addressing mods and using the given opcodes STCH = OX54 Buffer = 1000 0101 0100 (00) 1 (x) 000 1000 0000 0000 () 011 0000 0000 0000 () What will be target address? Briefly explain the usage of the JSUB and RSUB instruction sets in an SIC architecture coding
(4) Suppose address of IMR in 8259A is 21H, ① please write a program section which unmasks IRR2 interrupt and does not change other interrupt’s statue. ② please write a program section which masks IRR4-IRR6 interrupt and does not change other interrupt’s statue
Find the correct matching between explanations in (a), (b) and (c) and corresponding definitions in (i),(ii), (iii) and (iv): (a) An interrupt can be postponed when a higher priority interrupt has arrived(b) Execution of a program unexpectedly terminated by an interrupt (c) Clock of interrupt generator is in match with clock of the system clock (i) Normal(ii) Synchronous(iii) Maskable(iv) Exception
Suppose a specific MCU has the following size of memories: 2 M byte of flash, starting from 0x0800_0000, 256 k byte of SRAM starting from 0x2000_0000, and 8 k byte registers for GPIOs, start at 0x4001_0000. (Note that 0x is the prefix for hexadecimal numbers.) Draw the memory map based on your calculations for the addresses.
a) In the SRAM region, what is the corresponding bit-band alias address for the bit [4] of the memory address of 0 * 2000008 b) In the Peripheral region, if the value in the alias address 0 * 4200 0088 to 0 * 4200 008B was set to 0x00000001, what is the bit # and the address in the peripheral region that wants to set to 1?
Will upvote! Find the memory address of the next instruction executed by the microprocessor, when operated in the real mode, for the following CS:IP and 80286 register combinations: a. DS=2F2E & DX=9D64 b. CS=9F7A & IP=AB27 c. ES=DE21 & DI=D75F d. SS=FF5C & BP=92B8 e. DS=DC67 & CX=2FE8
1, Explain how we can find the address location of INT 0AH in Interrupt vector table. 2. What will be the content of AX register after execution of the instruction IMULCL, if CL = +1510 and AL = -13210.. 3. Suppose that DS = 1300H, SS = 1280H, BP = 15A0H and SI = 01D0H.Determine the address accessed by each of the following instructions andmention their type of addressing mode.i) MOV AX, [200H]ii) MOV AL, [BP-SI+200H]iii) ADD AL, [SI + 0100H]
Q1:Suppose the initial physical address of a segment register is given by 0E41:A02EH. Determine the physical address, base and final address of that segment register of 8086 microprocessor
Question 2: Write the MIPS code for the given Hexadecimal Machine Code that starts at memory address 0x40000. Line1: 0x0080082A Line2: 0x14200002 Line3: 0x2084FFFF Line4: 0x08010005 Line5: 0x20840001 Line6: 0x1480FFFA Line7: 0x03E00008 Line8: 0x0C010000
Two interrupts have execution times of 7.5us and 10 us. Both occur at the same rate, Find the maximum frequency that they can occur to maintain a combined CPU% less than 1.5%?