1. The resistance wire of a 1000 Watt iron is 40 cm long and has a diameter of D= 0.2cm. Determine the rate of heat generation in the wire per unit volume in W/cm3, and the heat flux on the outer surface of the wire, in W/cm2, as a result of the heat generation. q" D 2. Selected problems from the textbook (2.9, 2.10, 2.14)

1. The resistance wire of a 1000 Watt iron is 40 cm long and has a diameter of D= 0.2cm. Determine the rate of heat generation in the wire per unit volume in W/cm3, and the heat flux on the outer surface of the wire, in W/cm2, as a result of the heat generation. q" D 2. Selected problems from the textbook (2.9, 2.10, 2.14)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.10P: 1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss...

See similar textbooks

Similar questions

3.17 A 1.4-kg aluminum household iron has a 500-W heating element. The surface area is . The ambient temperature is 21°C, and the surface heat transfer coefficient is . How long after the iron is plugged in does its temperature reach 104°C?
A thin-wall jacketed tank heated by condensing steam at one atmosphere contains 91 kg of agitated water. The heat transfer area of the jacket is 0.9m2 and the overall heat transfer coefficient U=227W/m2K based on that area. Determine the heating time required for an increase in temperature from 16C to 60C.
1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a well-insulated 40-L tank of water that is initially at 300 K. If each heater dissipates 500 W, what is the time required for bringing the water temperature in the tank to 340 K? State your assumption for your analysis.
A cooling system is to be designed for a food storage warehouse for keeping perishable foods cool prior to transportation to grocery stores. The warehouse has an effective surface area of 1860 m2 exposed to an ambient air temperature of 32C. The warehouse wall insulation (k=0.17W/(mK)) is 7.5 cm thick. Determine the rate at which heat must be removed (W) from the warehouse to maintain the food at 4C.
2.55 A long, 1-cm-diameter electric copper cable is embedded in the center of a 25-cm-square concrete block. If the outside temperature of the concrete is 25oC and the rate of electrical energy dissipation in the cable is 150 W per meter length, determine temperatures at the outer surface and at the center of the cable.
2.44 To determine the thermal conductivity of a long, solid 2.5-cm-diameter rod, one half of the rod was inserted into a furnace while the other half was projecting into air at . After steady state had been reached, the temperatures at two points 7.6 cm apart were measured and found to be and , respectively. The heat transfer coefficient over the surface of the rod exposed to the air was estimated to be 22.7 . What is thermal conductivity of the rod?
2.46 The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of with a heat transfer coefficient of . On the other side of the heat exchanger wall flows a gas, and the wall has 96 thin rectangular steel fins 0.5 cm thick and 1.25 cm high as shown in the accompanying sketch. The fins are 3 m long and the heat transfer coefficient on the gas side is . Assuming that the thermal resistance of the wall is negligible, determine the rate of heat transfer if the overall temperature difference is .
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
2.2 A small dam, which is idealized by a large slab 1.2 m thick, is to be completely poured in a short Period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3. If both dam surfaces are at 16°C, determine the maximum temperature to which the concrete will be subjected, assuming steady-state conditions. The thermal conductivity of the wet concrete can be taken as 0.84 W/m K.
8.15 A mercury bath at is to be heated by immersing cylindrical electric heating rods, each 20 cm tall and 2 cm in diameter. Calculate the maximum electric power rating of a typical rod if its maximum surface temperature is .
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.