The wall of a cold room consists of a layer of cork sandwiched between outer and inner walls of wood, the wood walls being each 30 mm thick. The inside atmosphere of the room is maintained at -20 °C when the external atmospheric temperature is 25 °C, the heat loss through the wall is 42 W/m2. Taking the thermal conductivity of wood and cork as 0.20 W/m-K and 0.05 W/m-K respectively, and the rate of heat transfer between each exposed wood surface and their respective atmospheres as 15 W/m2-K, calculate the thickness of the cork. (mm)

The wall of a cold room consists of a layer of cork sandwiched between outer and inner walls of wood, the wood walls being each 30 mm thick. The inside atmosphere of the room is maintained at -20 °C when the external atmospheric temperature is 25 °C, the heat loss through the wall is 42 W/m2. Taking the thermal conductivity of wood and cork as 0.20 W/m-K and 0.05 W/m-K respectively, and the rate of heat transfer between each exposed wood surface and their respective atmospheres as 15 W/m2-K, calculate the thickness of the cork. (mm)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.34P: A section of a composite wall with the dimensions shown below has uniform temperatures of 200C and...

See similar textbooks

Similar questions

1.37 Mild steel nails were driven through a solid wood wall consisting of two layers, each 2.5-cm thick, for reinforcement. If the total cross-sectional area of the nails is 0.5% of the wall area, determine the unit thermal conductance of the composite wall and the percent of the total heat flow that passes through the nails when the temperature difference across the wall is 25°C. Neglect contact resistance between the wood layers.
1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1
A high-speed computer is located in a temperature-controlled room at 26C. When the machine is operating, its internal heat generation rate is estimated to be 800 W. The external surface temperature of the computer is to be maintained below 85C. The heat transfer coefficient for the surface of the computer is estimated to be 10W/m2K. What surface area would be necessary to assure safe operation of this machine? Comment on ways to reduce this area.
1.2 The weight of the insulation in a spacecraft may be more important than the space required. Show analytically that the lightest insulation for a plane wall with a specified thermal resistance is the insulation that has the smallest product of density times thermal conductivity.
One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
As a designer working for a major electric appliance manufacturer, you are required to estimate the amount of fiberglass insulation packing (k = 0.035 W/m K) that is needed for a kitchen oven shown in the figure below. The fiberglass layer is to be sandwiched between a 2-mm-thick aluminum cladding plate on the outside and a 5-mm-thick stainless steel plate on the inside that forms the core of the oven. The insulation thickness is such that the outside cladding temperature does not exceed 40C when the temperature at the inside surface of the oven is 300C. Also, the air temperature in the kitchen varies from 15Cto33C, and the average heat transfer coefficient between the outer surface of the oven and air is estimated to be 12.0W/m2K. Determine the thickness of the fiberglass insulation that is required for these conditions. What would be the outer surface temperature when the inside surface of the oven is at 475C?
A steam pipe 200 mm in diameter passes through a large basement room. The temperature of the pipe wall is 500C, while that of the ambient air in the room is 20C. Determine the heat transfer rate by convection and radiation per unit length of steam pipe if the emissivity of the pipe surface is 0.8 and the natural convection heat transfer coefficient has been determined to be 10 W/m2K.
A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.
1.76 Explain a fundamental characteristic that differentiates conduction from convection and radiation.
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4